Skip to content
Omnikalc

Boussinesq vertical stress calculator

Enter the load, the depth and the horizontal offset to get the vertical stress increase in the soil, and compare it with the 2:1 spread method.

Updated on
Your inputs
kip

Value out of range

ft

Value out of range

ft

Value out of range

ft

Value out of range

ft

Value out of range

Results

Vertical stress increase at the offset (Boussinesq)

427 psf

Stress increase with the 2:1 method under the footing

595 psf

Influence factor I_B
0.2733
Stress increase on the load axis
746 psf
Contact pressure of the footing
4,167 psf
2:1 stress as a share of the contact pressure
14.3 %

The Boussinesq vertical stress calculator gives the vertical stress increase in the soil under a point load at a chosen depth and offset, the influence factor, the stress on the axis and the value from the 2:1 spread method for a footing.

How the calculation works

  • Enter the point load and the depth at which you want the stress.
  • Enter the horizontal offset from the load axis, 0 to read the stress straight below the load.
  • Enter the footing width and length to compare with the 2:1 method and the contact pressure.

Example

A load of 100 kip at a depth of 8 ft and an offset of 4 ft has an influence factor of 0.2733 and adds 427 psf. On the axis the increase is 746 psf. For a footing of 4 ft by 6 ft with a contact pressure of 4,167 psf, the 2:1 method gives 595 psf at that depth, 14.3 % of the contact pressure.

Why it matters

The calculator helps geotechnical engineering students, foundation designers and builders who need to know how much stress a footing, a tank or a stockpile adds to a soil layer at depth, the first step of a settlement or consolidation estimate and of a check of buried pipes and basements.

Good to know

Use the load and the lengths in consistent units: kips and feet in the US version, kilonewtons and meters in the metric version. The Boussinesq stress comes from a single concentrated force, so for a real footing sum the contributions of several point loads or use charts for a rectangular area. The 2:1 value is an average under the footing and is approximate. Both ignore layering, the stiffness of the footing and the soil weight, so confirm important cases with a full analysis.

The bearing capacity calculator checks the strength of the soil, the footing size calculator sizes the base, the settlement consolidation calculator turns the stress into a settlement and the effective stress calculator gives the stress already present in the soil.

Frequently asked questions

What does the Boussinesq equation give?

It gives the increase of vertical stress at a point inside an elastic, homogeneous half-space loaded by a point force at the surface. The stress is Q times the influence factor divided by the square of the depth, and the factor depends only on the ratio of the horizontal offset to the depth. It is the basis of most charts used for stress under footings and embankments.

What is the influence factor?

It is I_B = 3 / (2π) × [1 / (1 + (r/z)²)]^(5/2). On the axis (r = 0) it equals 3 / (2π), about 0.4775, and it falls quickly as the offset grows. At an offset equal to the depth it is only about 0.084.

How does the 2:1 method differ?

The 2:1 method assumes that the load spreads at a slope of two vertical to one horizontal, so the loaded area grows by the depth on each side. The stress is the load divided by (B + z)(L + z), an average value under the footing. It is a quick estimate that is easy to apply by hand.

What are the limits?

The theory assumes a linear elastic soil, a perfectly flexible point load and a half-space of infinite depth. Real soils are layered, stiff layers spread the load more widely, and a footing has a finite size. Use the results for settlement estimates and verify important cases with a more detailed analysis.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.