Skip to content
Omnikalc

Priming sugar calculator: how much sugar to carbonate your beer?

Enter the beer volume, target carbonation, temperature and sugar type to get the weight of priming sugar for the batch and for each bottle.

Updated on
Your inputs

Value out of range

Value out of range

°F

Value out of range

oz

Value out of range

Results

Priming sugar for the whole batch

111 g

A normal priming dose
Priming sugar in ounces
3.9 oz
Priming sugar per litre
5.85 g/L
Priming sugar per bottle
2.07 g
CO₂ already dissolved in the beer
0.86 volumes
CO₂ to produce in the bottle
1.54 volumes

Bottle conditioning turns a flat, fermented beer into a sparkling one: you add a measured amount of sugar, the yeast eats it and the CO₂ it produces stays dissolved in the sealed bottle. This calculator works out the weight of priming sugar for your batch from the volume, the carbonation you want and the temperature the beer reached, and tells you how much to put in each bottle.

How the calculation works

  • Residual CO₂ (volumes) = 3.0378 − 0.050062 × T + 0.00026555 × T², with T in °F (the highest temperature after fermentation)
  • CO₂ to produce = target volumes − residual volumes (never below zero)
  • Sugar per litre = CO₂ to produce × g/L per volume (3.8 sucrose, 4.2 dextrose, 5.4 dry malt extract)
  • Total sugar = sugar per litre × batch volume in litres

Example

5 gal (18.9 L) of beer at 68°F aimed at 2.4 volumes with table sugar. The beer already holds 0.86 volumes, so 1.54 volumes must come from the sugar. That is 1.54 × 3.8 = 5.85 g/L, or 111 g (3.9 oz) for the batch. In a 12 oz bottle this is about 2.07 g, roughly half a teaspoon.

Why it matters

Too little sugar gives a flat beer, and too much overcarbonates and can turn bottles into grenades. The dissolved CO₂ left over from fermentation is easy to forget, and it changes the answer by more than a gram per litre between a cold basement and a warm room. A calculated dose gives repeatable carbonation from one batch to the next.

Good to know

Dissolve the sugar in boiled water, cool it and mix it gently into the beer before bottling, without splashing, so the dose spreads evenly. Leave the bottles at room temperature for one to two weeks to carbonate, then chill. Use bottles rated for carbonation and wear eye protection when opening an overcarbonated one. This tool is for hobby brewing and education.

In practice

Weigh the sugar on a scale to 0.1 g rather than using spoons, and measure the finished volume after racking, not the starting volume. For kegs, the same target in volumes applies, but you carbonate with CO₂ gas at a set pressure and temperature instead of sugar.

The homebrew ABV calculator tracks alcohol, the keg servings calculator plans a party and the wine sulfite calculator protects bottled wine.

Frequently asked questions

How much priming sugar do I need to carbonate beer?

The amount depends on the batch volume, the carbonation you want and the CO₂ already dissolved in the beer. For 5 gallons aimed at 2.4 volumes of CO₂ at 68°F, about 3.9 oz (111 g) of table sugar is needed.

Why does the temperature matter?

Cold liquids hold more CO₂. The beer keeps the CO₂ it dissolved at the warmest temperature it reached after fermentation, so a warmer beer holds less and needs more priming sugar.

What are volumes of CO₂?

One volume means one litre of CO₂ gas (at standard conditions) dissolved in one litre of beer. Most ales sit at 2.0 to 2.6 volumes, lagers around 2.4 to 2.8, wheat beers 3.0 to 4.5, and cask ales 1.0 to 1.5.

Which sugar is best?

Table sugar and corn sugar both ferment cleanly and give neutral flavour. Dry malt extract ferments only partly, so a larger weight is needed, and it adds a little body. Never use more sugar than calculated: too much can burst the bottles.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.