Skip to content
Omnikalc

Strike water temperature calculator: how hot should the mash water be?

Enter the grain weight and temperature, the water to grain ratio and the target mash temperature to get the strike water temperature, the strike water volume and the total mash volume.

Updated on
Your inputs

Value out of range

qt/lb

Value out of range

°F

Value out of range

°F

Value out of range

Results

Strike water temperature

165.4 °F

Strike water volume

3.13 gal

Total mash volume
3.92 gal
Mash thickness
1.25 qt/lb

In all-grain brewing, the temperature of the mash decides the sugars that are made, so getting it right at the start is important. The strike water temperature has to be higher than the target to allow for the cooling when the cold grain goes in. This strike water temperature calculator takes the grain weight and temperature, the water to grain ratio and the target mash temperature to give the strike water temperature, the strike water volume and the total mash volume.

How the calculation works

  • Strike temperature = (0.2 ÷ ratio) × (target − grain temperature) + target, with the ratio in quarts of water per pound of grain and temperatures in °F. The 0.2 is the specific heat of the grain compared with that of water.
  • Strike water volume = grain weight × ratio ÷ 4, converting quarts to gallons.
  • Mash volume = water volume + the volume taken by the grain, about 0.08 gallon per pound.
  • Mash thickness is the ratio itself. Thin mashes (over 2 qt/lb) are more fermentable, and thick ones (1 to 1.25 qt/lb) give a fuller body.

Example

You mash 10 lb of grain at 68 °F to reach 152 °F with 1.25 qt/lb. The strike water temperature is (0.2 ÷ 1.25) × (152 − 68) + 152 = 165.4 °F. The strike water volume is 10 × 1.25 ÷ 4 = 3.13 gallons, and the total mash volume is about 3.9 gallons.

Why it matters

Hitting the mash temperature within a degree or two on the first try saves the effort of adding hot or cold water and gives a beer that matches the recipe. The volume figures help you check that the mash fits in the tun and that the water in the kettle is enough.

Good to know

The formula is the standard simple infusion equation and works well in a room-temperature setting with a well insulated tun. It does not take into account the heat absorbed by the mash tun, which depends on its material and its starting temperature, and many brewers add a correction after a few batches. The grain temperature should be measured, since grain stored in a cold garage is much colder than the room. Water volume does not include the losses to the grain, which absorbs about 0.5 gallon per pound.

The homebrew ABV calculator estimates the alcohol of the beer, the priming sugar calculator sets the carbonation and the keg servings calculator counts the pours.

Frequently asked questions

What is strike water?

It is the hot water that is mixed with the crushed grain at the start of the mash. Its temperature must be higher than the target mash temperature because the cold grain cools it down when they are mixed.

What mash temperature should I aim for?

A mash at 148 to 150 °F gives a more fermentable wort, a drier beer and a lighter body. A mash at 154 to 158 °F gives a less fermentable wort and a sweeter and fuller beer. Most recipes use 152 °F as a middle value.

What water to grain ratio is typical?

Most all-grain brewers use 1.25 to 1.5 quarts per pound, which is a thick mash. Thinner mashes of 2 quarts per pound or more are used for some styles and in brew-in-a-bag methods. Thicker mashes keep their temperature better.

Why is my mash temperature different from the calculation?

The formula ignores the heat taken by the mash tun and the air. A cold cooler or kettle takes heat, so preheat it with hot water and add a few degrees if needed. Measure the temperature in several places after stirring, and adjust with cold or hot water.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.