Skip to content
Omnikalc

Amplifier damping factor calculator: how much your speaker cable reduces the damping

Enter the speaker impedance, the damping factor of the amplifier, the cable length and the wire gauge to get the effective damping factor, the cable resistance, the voltage lost and the level loss.

Updated on
Your inputs
Ω

Value out of range

Value out of range

ft

Value out of range

Results

Effective damping factor with the cable

31.9

Good control of the woofer
Resistance of the cable (round trip)
201 mΩ
Share of the voltage lost in the amp output and the cable
3.04%
Level loss
0.27 dB
Output impedance of the amplifier
50 mΩ

The damping factor tells how well an amplifier controls the speaker. The amplifier damping factor calculator gives the effective damping factor once the speaker cable is added, the resistance of the cable, the voltage lost in the output and the cable, the level loss in decibels and the output impedance of the amplifier.

How the calculation works

  • Enter the impedance of the speaker in ohms, such as 4, 6 or 8 Ω.
  • Enter the damping factor of the amplifier from its specifications. It is the speaker impedance divided by the output impedance of the amplifier, usually quoted at 8 Ω and at a low frequency.
  • Enter the length of the speaker cable, one way, and its gauge. The current goes out and comes back, so the cable counts twice.
  • The calculator finds the output impedance and the resistance of the cable, then the effective damping factor = speaker impedance / (output impedance + cable resistance), the voltage lost and the level loss in decibels.

Example

An amplifier has a damping factor of 160 into 8 Ω, which means an output impedance of 8 / 160 = 50 mΩ. The speaker cable is 25 ft of 16 AWG, which has 4.016 Ω per 1,000 ft. The round trip is 2 × 25 ft, so the resistance is 200.8 mΩ. The effective damping factor drops to 8 / (0.050 + 0.2008) = 31.9. The amplifier and the cable lose 3.04 % of the voltage, which is a level loss of 0.27 dB.

Why it matters

The calculator helps audio enthusiasts, installers and students to choose the right gauge and length of a speaker cable, to compare amplifiers fairly and to see that the cable matters more than a high damping factor on a data sheet. It gives the numbers to decide when a thicker cable is worth buying.

Good to know

The damping factor of an amplifier changes with the frequency and the load, and manufacturers quote the best case. The calculator uses the resistance only and ignores the inductance and the capacitance of the cable, which are small for normal lengths. Keep the cable as short as practical, and use a thicker gauge for a low-impedance speaker or a long run.

The speaker wiring calculator connects several speakers in series and parallel, the speaker SPL calculator estimates the sound level, the speaker crossover calculator designs the filters, and the decibel addition calculator combines levels.

Frequently asked questions

What is the damping factor of an amplifier?

The damping factor is the impedance of the speaker divided by the output impedance of the amplifier. It tells how well the amplifier holds the cone of the speaker under control when the music stops: a low output impedance acts as an electrical brake. The figure is usually given for an 8 Ω load at 1 kHz or lower.

How does the speaker cable change the damping factor?

The cable is in series between the amplifier and the speaker, and its resistance adds to the output impedance. A thin or long cable can lower the effective damping factor a lot, even with an amplifier that has a high damping factor. The calculator takes the round trip into account, as the current goes through two conductors.

What damping factor do I need?

A damping factor above 20 to 30 at the speaker is enough in practice for most speakers, and few listeners hear a difference above 50. The effect is largest at the resonance of the woofer, at low frequencies. A larger wire gauge and a shorter cable are the easiest ways to keep the damping high.

Does the cable also reduce the volume?

The cable and the output impedance form a voltage divider with the speaker, so a fraction of the voltage is lost. With a few tenths of an ohm in series with an 8 Ω speaker, the loss is a few percent, a fraction of a decibel. It is small, but it grows for speakers of low impedance, which have a larger current.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.