Skip to content
Omnikalc

Class B push-pull amplifier calculator

Enter the supply voltage, the load and the output swing to get the output power, the supply power, the efficiency and the dissipation per transistor.

Updated on
Your inputs
V

Value out of range

Ω

Value out of range

V

Value out of range

Results

Output power

9.00 W

Efficiency

62.8 %

Dissipation per transistor

2.66 W

Power drawn from the supply
14.32 W
Worst-case dissipation per transistor (at Vp = 2Vcc/π)
2.85 W
Maximum output power (Vp = Vcc)
14.06 W
Maximum efficiency (Vp = Vcc)
78.5 %

The class B push-pull amplifier calculator gives the output power, the power drawn from the supply, the efficiency, the dissipation per transistor, the worst-case dissipation and the maximum power and efficiency, for a sine wave across a resistive load.

How the calculation works

  • Enter the supply voltage of each rail, positive and negative.
  • Enter the load resistance, for example 8 ohms for a loudspeaker.
  • Enter the peak output voltage and read the powers and the efficiency.

Example

With supplies of ±15 V, a load of 8 Ω and a peak swing of 12 V, the amplifier delivers 9.00 W while drawing 14.32 W, an efficiency of 62.8 %. Each transistor dissipates 2.66 W, and the worst case is 2.85 W. At full swing, the output reaches 14.06 W with an efficiency of 78.5 %.

Why it matters

The calculator helps electronics students, audio builders and engineers who design the output stage of a power amplifier, a headphone driver or a motor driver, and who need to size the supply and the heat sinks and to compare the efficiency of the classes of operation.

Good to know

The calculation is for an ideal complementary pair driven by a sine wave into a resistive load, ignoring the saturation voltages of the transistors, the emitter resistors and the quiescent current of class AB. Real amplifiers reach a lower swing than the supply, and music has a lower average power than a sine wave, so the average dissipation is less than the sine figure. Size the heat sinks for the worst-case dissipation and the supply for the peak current. Add the protection against short circuits.

The amplifier damping factor calculator relates the output impedance and the load, the op-amp gain calculator sets the gain of the driver stage, the transistor base resistor calculator biases the drivers and the sound power level calculator converts power to decibels.

Frequently asked questions

What is a class B push-pull amplifier?

It is an output stage with two complementary transistors, one that conducts during the positive half of the signal and one during the negative half, each for 180 degrees of the cycle. With no signal, neither conducts, so the quiescent power is nearly zero. This gives a much better efficiency than class A, at the cost of crossover distortion.

How is the efficiency computed?

With a sine wave of peak Vp across the load RL, the output power is Vp² / (2 RL) and the power drawn from the two supplies is 2 Vcc Vp / (π RL). The efficiency is therefore π Vp / (4 Vcc), which reaches the theoretical maximum of π/4, or 78.5 percent, when the swing reaches the supply voltage.

Why is the worst-case dissipation not at full power?

The dissipation in each transistor rises with the swing, reaches a maximum of Vcc² / (π² RL) at a peak voltage of 2 Vcc / π, about 64 percent of the supply, and then falls as the efficiency rises. The heat sink must be sized for this worst case and not for full output.

How does class AB fix the crossover distortion?

Class AB biases both transistors slightly on, with a small quiescent current, so that one takes over smoothly from the other near the zero crossing. This removes most of the crossover distortion with only a small loss of efficiency. This calculator treats the ideal class B case, which is the limit of class AB at small bias.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.