Skip to content
Omnikalc

Aquaponics stocking calculator: how many fish do I need for my grow bed?

Enter the grow bed area, the tank volume and the feeding figures to get the daily feed, the fish biomass needed, the tank capacity and the number of fish.

Updated on
Your inputs

Value out of range

Value out of range

g/m²/day

Value out of range

% of body weight per day

Value out of range

kg per 1,000 L

Value out of range

Value out of range

Results

Fish biomass needed

11.9 kg

The tank holds the fish needed with room to spare
Daily feed to balance the grow bed
178 g
Fish biomass the tank can hold
15.1 kg
Number of fish
52

The balance between the fish and the plants decides whether an aquaponic system thrives or crashes, and many beginners guess. This aquaponics stocking calculator takes the grow bed area, the tank volume, the feed per square meter, the feeding rate of the fish, the safe stocking density and the average fish weight to give the daily feed, the fish biomass needed, the biomass the tank can hold and the number of fish.

How the calculation works

  • Daily feed = grow bed area × feed per square meter, with the area in square meters. A common design figure is 40 to 60 grams of fish feed per square meter of media bed per day.
  • Fish biomass needed = daily feed ÷ feeding rate. Fish eat a share of their body weight each day, about 1% to 2% for adult tilapia.
  • Biomass the tank can hold = tank volume in liters × safe stocking density ÷ 1,000. Systems commonly run at 10 to 20 kg of fish per 1,000 L.
  • Number of fish = biomass needed ÷ average weight of one fish. If the biomass needed is more than the tank can hold, the tank is too small for the grow bed.

Example

A grow bed of 32 ft² (2.97 m²) takes 60 g/m²/day, so the daily feed is 178 g. At a feeding rate of 1.5%, the fish biomass needed is 178 ÷ 0.015 = 11.9 kg. A tank of 200 gal (757 L) at 20 kg per 1,000 L can hold 15.1 kg, so it holds the fish needed with room to spare. With fish of 8 oz (227 g), that is about 52 fish.

Why it matters

Hobbyists and small growers use the calculation before they buy fish to check that the tank and the grow bed are in proportion. A system with too few fish starves the plants of nutrients, and one with too many fish pollutes the water and stresses the animals.

Good to know

The figures are design guidelines from the aquaponics community and not exact rules. Water temperature, the type and size of the fish, the plants, the bed depth and the filtration change the right balance. Fish grow, so the biomass rises over time, and the system should be checked for ammonia, nitrite and nitrate. Check local rules for keeping fish, and do not release them into the wild.

The fish feeding calculator sets the daily ration for aquarium and pond fish, and the feed conversion ratio calculator measures how well animals turn feed into weight.

Frequently asked questions

What is aquaponics?

Aquaponics combines fish farming with growing plants in water. The fish are fed, and their waste is turned by bacteria into nutrients that feed the plants. The plants clean the water, which goes back to the fish. A well-balanced system needs the right ratio between the feed that goes in and the area of plants that use it.

What is the feed rate ratio method?

The feed rate ratio is a design method in which you size the system from the daily amount of fish feed per area of grow bed. A common figure for media beds is 40 to 60 grams of feed per square meter per day. The feed gives the nutrients for the plants, and the fish needed to eat it follow from their feeding rate.

What stocking density is safe?

Many backyard systems run at around 10 to 20 kilograms of fish per 1,000 liters of tank, which is about 1 pound per 5 to 10 gallons. Higher densities need strong filtration, aeration and careful monitoring, and low densities are more forgiving. Start low and increase gradually.

What if the tank is too small?

If the fish biomass needed is more than the tank can safely hold, reduce the grow bed area, add a bigger tank, add a second tank, or add more filtration and aeration. A system can also run with a lower feed rate per area, in which case leafy plants do better than fruiting plants.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.