Skip to content
Omnikalc

Center pivot irrigation depth calculator

Enter the radius of the pivot, the speed of the end tower, the flow rate and the efficiency to get the revolution time, the gross and net depth per pass and the pumping hours needed each week.

Updated on
Your inputs
ft

Value out of range

ft/min

Value out of range

gpm

Value out of range

%

Value out of range

in

Value out of range

Results

Time for one revolution

19.4 h

Gross depth per revolution

0.28 in

Net depth per revolution

0.24 in

Irrigated area
121.9 ac
Revolutions needed per week
6.3
Pumping hours needed per week
122 h
Share of the week of 168 hours
72 %

The center pivot irrigation depth calculator gives the revolution time, the gross and net water depth applied per pass, and the revolutions and pumping hours per week that cover the water need of the crop, from the radius, the end tower speed and the flow.

How the calculation works

  • Enter the radius of the irrigated circle and the speed of the end tower.
  • Enter the flow rate of the pivot and its application efficiency.
  • Enter the crop water need per week and read the depth per pass and the hours of pumping.

Example

A pivot of 1300 ft radius irrigates 121.9 ac. With the end tower at 7 ft/min, one revolution takes 19.4 h. With a flow of 800 gpm, each pass applies 0.28 in gross, so 0.24 in reaches the roots at the chosen efficiency. To cover a need of 1.5 in per week, the pivot must turn 6.3 times, which is 122 h of pumping or 72 % of the week.

Why it matters

The calculator helps farmers, irrigation managers and students who run a center pivot and need to set the speed percentage for a target depth, or check whether the system can keep up with the peak water demand of the crop during a hot week.

Good to know

Use the radius that is really wetted, including the end gun if it is on, and the true flow measured by a meter, not the nameplate value. The speed of the end tower is given by the percent timer setting and the full-speed value of the machine. Remember that the depth per pass is the average on the whole circle. A pivot that can only deliver a small depth per pass has to turn often, and the risk of runoff and evaporation grows. If the pumping hours exceed the available week, the system is undersized for the crop.

The crop water need calculator estimates the demand of the crop, the drip irrigation calculator sizes micro-irrigation, the reference evapotranspiration calculator gives the weather demand and the available water capacity calculator describes the soil reservoir.

Frequently asked questions

How long does a center pivot take to turn?

The end tower travels a circle of circumference 2πR. Dividing by the speed of that tower gives the revolution time. A pivot of 1300 feet radius whose end tower moves at 7 feet per minute needs about 19 hours for a full turn. The inner towers move more slowly, in proportion to their distance from the pivot point.

How is the depth per revolution calculated?

The volume pumped during one revolution is the flow rate multiplied by the revolution time. This volume is spread over the area of the circle, πR². Dividing one by the other gives the gross depth, in inches or millimeters. Because the pivot turns slower at lower speed, the depth is inversely proportional to the speed of the end tower.

What is the application efficiency?

Not all the water that leaves the nozzles reaches the root zone. Evaporation, drift and runoff cause losses. A modern low-pressure pivot reaches 85 to 95 percent, an older high-pressure one 75 to 80 percent. The net depth is the gross depth multiplied by the efficiency.

Does this show runoff risk?

No. The depth per pass is an average over the whole circle. The water is actually applied at a high instantaneous rate near the outer end, so an infiltration problem can occur even with a small depth. Check the peak application rate of your nozzle package against the infiltration of the soil.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.