Skip to content
Omnikalc

Christiansen uniformity coefficient calculator

Enter the depth caught in eight cans and the duration of the test to get the Christiansen uniformity coefficient, the scheduling coefficient, the precipitation rate and a quality class.

Updated on
Your inputs
in

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

h

Value out of range

Results

Christiansen uniformity coefficient (CU)

89.7 %

Scheduling coefficient (mean divided by lowest)

1.32

Mean depth caught
0.290 in
Lowest can
0.220 in
Highest can
0.340 in
Precipitation rate
0.290 in/h
Quality class (3 excellent from 90, 2 good from 80, 1 fair from 70, 0 poor)
2

The Christiansen uniformity coefficient calculator gives the CU of a sprinkler system from the depths caught in eight cans, together with the mean depth, the scheduling coefficient, the precipitation rate and a quality class.

How the calculation works

  • Run the sprinklers for a measured time and enter the depth in each of the eight cans.
  • Enter the duration of the test in hours.
  • Read the CU, the scheduling coefficient, the precipitation rate and the class.

Example

The eight cans give a mean of 0.290 in, with a lowest value of 0.220 in and a highest value of 0.340 in. The Christiansen uniformity coefficient is 89.7 %. The scheduling coefficient is 1.32: to be sure that the driest spot gets enough, you apply that multiple of the target depth. The precipitation rate is 0.290 in/h, and the quality class is 2.

Why it matters

The calculator helps landscape contractors, turf managers, farmers and students who audit a sprinkler system, find out whether the heads are well spaced and the pressure is right, and compute how long to run a zone to deliver a given depth.

Good to know

Use identical straight-sided containers, place them on a regular grid, and keep them away from the edge of the wetted area. Run the test with little wind, at the normal operating pressure, and for long enough to catch a measurable depth. Eight cans are only a quick check, so for a full audit use a grid of many more, covering the whole area between four heads. The formula gives equal weight to every can and does not penalize a single very dry spot, which is why the scheduling coefficient is useful as a second measure. Repeat the test after any repair.

The sprinkler run time calculator turns a depth into minutes per zone, the crop water need calculator gives the depth to apply, the drip irrigation calculator sizes micro-irrigation and the center pivot irrigation depth calculator handles large machines.

Frequently asked questions

What is the Christiansen uniformity coefficient?

It is the standard measure of how evenly a sprinkler system applies water. It was proposed by Christiansen in 1942 and is computed from the depths in a grid of catch cans as CU = 100 × [1 − Σ|xi − mean| / (n × mean)]. A value of 100 percent is perfectly uniform, and the value decreases as the cans differ more from the average.

How do I carry out the test?

Place a series of identical straight-sided containers on a regular grid between the sprinklers, run the system for a set time, usually an hour, and measure the depth in each one. Do the test in light wind. This calculator takes eight cans, which is a simple check, while a standard test uses many more and covers the full spacing of the heads.

What is the scheduling coefficient?

It is the ratio of the mean depth to the lowest depth. To make sure that the driest spot receives the water that the plant needs, you have to apply the target depth multiplied by this coefficient. A value of 1.5 means that you have to apply 50 percent more water than the need to avoid dry patches, and this wastes water.

What is a good uniformity?

For a lawn or turf, a CU of 80 percent or more is usual, and 90 percent is excellent. For field crops with a sprinkler system, 75 to 85 percent is common. A low value comes from wrong head spacing, pressure that is too high or too low, worn nozzles, wind or a mix of different nozzles.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.