Skip to content
Omnikalc

Langelier saturation index calculator: balance pool and tap water

Enter the pH, temperature, calcium hardness, alkalinity and dissolved solids to get the Langelier saturation index, the pH of saturation and the Ryznar index of water.

Updated on
Your inputs

Value out of range

°F

Value out of range

ppm as CaCO₃

Value out of range

ppm as CaCO₃

Value out of range

ppm

Value out of range

Results

Langelier saturation index (LSI)

0.10

Balanced water: little scaling and little corrosion
pH of saturation (pHs)
7.50
Ryznar stability index (RSI)
7.41

Will your water leave scale or eat your pipes? The Langelier saturation index calculator compares the pH of the water with the pH at which calcium carbonate is in equilibrium, from the temperature, calcium hardness, alkalinity and dissolved solids. It gives the LSI, the pH of saturation and the Ryznar index.

How the calculation works

  • Enter the pH, the temperature, the calcium hardness and the total alkalinity of the water (both as CaCO₃), and the total dissolved solids (TDS).
  • The calculator computes the pH of saturation pHs, the pH at which the water would be in equilibrium with calcium carbonate.
  • The Langelier saturation index is LSI = pH − pHs. The pHs is found from the terms A (TDS), B (temperature), C (calcium) and D (alkalinity): pHs = (9.3 + A + B) − (C + D).
  • A value near 0 (between −0.3 and +0.3) is balanced. A negative value means corrosive water, and a positive one means scale-forming water.

Example

A swimming pool at 82 °F has a pH of 7.6, a calcium hardness of 300 ppm, an alkalinity of 90 ppm and 1,000 ppm of TDS. The pH of saturation is 7.50, so the LSI is 7.6 − 7.50 = +0.10. The water is balanced. The Ryznar index is 7.41.

Why it matters

The balance of the water protects the surfaces and the equipment of a pool, a boiler or a cooling system, and it avoids both scale and corrosion. The index is the standard tool used by pool operators, water utilities and plumbers to decide how to treat water before damage appears.

Good to know

The index predicts the tendency of water to deposit or dissolve calcium carbonate, not the rate. It is a thermodynamic estimate that does not account for the effects of other ions, such as magnesium, borates and cyanuric acid, which change the real alkalinity of a pool, nor for the presence of inhibitors or of a protective film. The alkalinity should be corrected for cyanuric acid in a pool, and the formula is accurate for temperatures from 32 to 200 °F and pH from 6.5 to 9.5.

The water hardness calculator converts hardness between units, the pool chlorine calculator gives the sanitizer dose, the pH calculator covers the acidity of the water, and the aquarium CO₂ calculator links the pH, alkalinity and dissolved gas.

Frequently asked questions

What is the Langelier saturation index?

It is a number that tells whether water will deposit calcium carbonate (scale) or dissolve it (corrosion). It is the difference between the actual pH of the water and the pH at which the water would be exactly saturated with calcium carbonate. It was proposed by Wilfred Langelier in 1936 for municipal water systems and is also used for pools, boilers and cooling towers.

How do I read the result?

A value between −0.3 and +0.3 is balanced. Below −0.3, the water is aggressive: it etches plaster and grout and attacks metals and heat exchangers. Above +0.3, it is scale-forming: it leaves white deposits on tiles, in pipes and on heaters, and it can make the water cloudy. A pool is generally kept near 0, between −0.3 and +0.3.

How can I correct the index?

To raise the index of corrosive water, add alkalinity (with sodium bicarbonate), calcium (with calcium chloride) or raise the pH. To lower the index of scale-forming water, lower the pH or the alkalinity, usually by adding acid, or dilute the water. Temperature is an important factor: hot water is much more scale-forming than cold water, which is why scale builds up in heaters.

What is the Ryznar index?

The Ryznar stability index, RSI = 2 pHs − pH, uses the same data. It is below 6 for scale-forming water, between 6 and 7 for water about in balance and above 7 for water that tends to corrode, more so as the value rises. Unlike the Langelier index, the sign is reversed: a high RSI is corrosive, and it gives a better idea of the intensity of scaling or corrosion.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.