Skip to content
Omnikalc

How wide should a wooden gate be and how long is the brace?

Enter the opening between posts, the gate height, the clearance for hinges and latch, the rail inset, the board width and the gap: get the gate width, the diagonal brace length, the boards, the board length and the frame lumber.

Updated on
Your inputs
in

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

Results

Gate width

47.00 in

Diagonal brace

59.2 in

Boards
9
Board length
36.0 ft
Frame lumber (2 rails and brace)
12.8 ft
Run the brace up from the bottom hinge corner to the top latch side so it holds the gate in compression and stops it sagging

A simple wooden garden gate has two horizontal rails, a diagonal brace and vertical boards. To fit and swing well, it must be a little narrower than the opening, and the brace must run the right way so the gate does not sag. This calculator works out the gate width, the brace length, the boards and the lumber.

How the calculation works

  • Gate width = opening between posts − total clearance for hinges and latch
  • Brace length = √(gate width² + (height − 2 × rail inset)²)
  • Boards = gate width ÷ (board width + gap), rounded up
  • Board length = boards × gate height
  • Frame lumber = 2 rails × gate width + brace length

A 48 in opening with 1 in of total clearance takes a gate 47 in wide. At 48 in high, with the rails 6 in from the top and bottom, the brace is about 59.2 in long. With 5.5 in boards and 1/4 in gaps, it takes 9 boards, 36 ft of boards and about 12.8 ft of frame lumber.

Common sizes

Gate Opening width
Garden path, one person 36 to 42 in
Wheelbarrow and lawn mower 42 to 48 in
Garden tractor or small cart 60 in or more, often a double gate

For an opening wider than about 4 ft, a single wooden gate gets heavy and tends to sag: use a double gate, a metal frame or a wheel at the latch end.

Which way the brace goes

The brace must run from the bottom corner on the hinge side up to the top corner on the latch side. That way it works in compression, pushing the latch side up and stopping the gate from drooping. A brace put in the other way pulls apart and does almost nothing. A Z-shaped frame is the simplest option; a full rectangular frame with a brace is stronger.

Clearance

Leave about 1/2 in on the hinge side and 1/2 in on the latch side, a little more in wet climates where wood swells. Allow 2 in or more at the bottom so the gate clears the ground, grass and snow, and more on sloping ground.

Hardware and posts

Use heavy strap hinges or T-hinges screwed into the rails, not just the boards, and a gravity latch or a self-closing hinge if children or pets need to stay in. The hinge post carries the whole weight of the gate: set it at least 2 ft deep, in concrete for a heavy gate, and make it thicker than the other fence posts. Galvanized or stainless hardware will not stain the wood.

Frequently asked questions

How wide should a gate be for a 48 in opening?

About 47 in, leaving about 1/2 in on each side for hinges and latch.

How long is the brace on a 4 ft gate?

On a 47 × 48 in gate with rails 6 in from the edges, about 59.2 in.

Which way should a gate brace go?

From the bottom hinge corner up to the top latch corner, so it works in compression.

How many boards for a 4 ft gate?

9 boards of 5.5 in with 1/4 in gaps, or 36 ft of boards at 48 in high.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.