Skip to content
Omnikalc

How do you calculate pulmonary vascular resistance?

Enter the mean pulmonary artery pressure, the wedge pressure and the cardiac output: get PVR in Wood units and dyn·s/cm⁵, the gradient and the indexed value.

Updated on

Educational tool, not medical advice: this page does not diagnose and does not replace a doctor, nurse or pharmacist. It has not been reviewed by a healthcare professional. Editorial and medical policy

Your inputs
mmHg

Value out of range

mmHg

Value out of range

L/min

Value out of range

m²

Value out of range

Results

Pulmonary vascular resistance

4.60 Wood units

Above 2 Wood units: raised pulmonary vascular resistance
Pulmonary vascular resistance
368 dyn·s/cm⁵
Transpulmonary gradient
23 mmHg
Indexed resistance (PVRI)
8.74 WU·m²

Blood flows through the lungs at low pressure, in vessels that are normally wide and compliant. When these vessels narrow or get blocked, as in pulmonary hypertension, the resistance to flow rises. Pulmonary vascular resistance (PVR) puts a number on this. It is calculated from values measured during right heart catheterization: the mean pulmonary artery pressure, the wedge pressure and the cardiac output. This calculator gives PVR in Wood units and in dyn·s/cm⁵, and indexes it to body size.

How the calculation works

  • Transpulmonary gradient = mean pulmonary artery pressure − pulmonary artery wedge pressure
  • PVR (Wood units) = transpulmonary gradient ÷ cardiac output
  • PVR (dyn·s/cm⁵) = Wood units × 80
  • PVR index = PVR × body surface area

Example

A patient has a mean pulmonary artery pressure of 35 mmHg, a wedge pressure of 12 mmHg and a cardiac output of 5 L/min. The transpulmonary gradient is 23 mmHg, so PVR is 23 ÷ 5 = 4.6 Wood units, or 368 dyn·s/cm⁵. With a body surface area of 1.9 m², the indexed resistance is 8.74 WU·m². This is above the normal range and suggests that the lung vessels themselves contribute to the high pressure.

Why it matters

PVR helps separate the causes of high pulmonary pressure. If the wedge pressure is high but PVR is normal, the problem is usually on the left side of the heart. If PVR is high, the lung vessels themselves are involved. PVR is also checked before heart transplantation, because a persistently high value can make a donor heart fail, and it is followed during treatment of pulmonary arterial hypertension.

Good to know

The result is only as good as the measurements. Pressures must be read at end-expiration, the transducer must be zeroed at the right level and the cardiac output should be measured by thermodilution or by the Fick method. Thresholds vary by guideline and by indication, so the numbers here are broad reference points.

The cardiac output calculator gives the flow value used here, the BSA calculator gives the body surface area, and the A-a gradient calculator evaluates oxygen exchange in the lungs.

Frequently asked questions

What is pulmonary vascular resistance?

It measures how hard it is for blood to flow through the lungs' blood vessels. It is the pressure drop across the lungs, the mean pulmonary artery pressure minus the wedge pressure, divided by the cardiac output.

What are Wood units?

The pressure drop in mmHg divided by the flow in L/min. One Wood unit equals 80 dyn·s/cm⁵. Both units describe the same resistance and doctors convert between them.

What is a normal value?

Usually 0.3 to 2 Wood units (about 25 to 160 dyn·s/cm⁵). In 2022, European guidelines set a PVR above 2 Wood units, with a mean pressure above 20 mmHg, as a criterion for pre-capillary pulmonary hypertension.

Is this a diagnosis?

No. PVR is measured by right heart catheterization and interpreted together with the clinical picture by a cardiologist or pulmonologist. This calculator is educational.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.