Skip to content
Omnikalc

Archimedean spiral calculator

Enter the starting radius, the spacing between successive turns and the number of turns of the spiral r = r₀ + bθ to get the final radius, the exact arc length, the length estimated with the mean circumference and the area swept.

Updated on
Your inputs
cm

Value out of range

cm

Value out of range

Value out of range

Results

Final radius

3.500 cm

Arc length of the spiral

70.736 cm

Estimate with the mean circumference
70.686 cm
Area swept by the radius
87.703 cm²
Parameter b (radius gain per radian)
0.0796 cm
Average length per turn
14.137 cm
Width of the wound band
2.500 cm

The Archimedean spiral calculator gives the final radius, the exact arc length, the estimate with the mean circumference, the area swept and the width of the wound band of the spiral r = r₀ + bθ from its starting radius, the spacing between turns and its number of turns.

How the calculation works

  • Enter the starting radius, for example the core of a roll.
  • Enter the spacing between successive turns, such as the thickness of the material.
  • Enter the number of turns and read the length and the final radius.

Example

A spiral from a radius of 1 cm with a spacing of 0.5 cm between turns and 5 turns reaches a radius of 3.500 cm, a band of 2.500 cm. Its exact length is 70.736 cm, against 70.686 cm with the mean circumference, and it sweeps 87.703 cm². Each turn is 14.137 cm long on average.

Why it matters

The calculator helps makers, technicians and students who need the length of tape, wire, rope, film or paper wound on a core, the length of a groove on a record or a coil, or who study polar curves, and prefer a quick result to carrying out the integral by hand.

Good to know

The spacing between turns is the thickness of one layer, so use the real thickness of the material and not the nominal one. The turns can be fractional, in steps of half a turn. The starting radius must be above zero for a roll with a core, and zero is allowed for a spiral that starts at the center. The exact formula and the estimate agree closely for tight spirals. Material that is compressed, stretched or wound unevenly will differ. Use the same unit for the radius and the spacing.

The logarithmic spiral calculator treats the spiral with a constant growth factor, the spiral curve length calculator handles road transition curves, the helix length calculator measures a coil in three dimensions and the circle calculator gives circumferences.

Frequently asked questions

What is an Archimedean spiral?

It is the curve r = r₀ + bθ, in which the radius grows by a constant amount for every turn. Successive turns are always separated by the same distance 2πb. A rolled carpet, a coil of rope, the groove of a vinyl record and the track of a CD all follow this type of spiral. It is described in Archimedes’s book On Spirals.

How is the arc length computed?

For r = bθ, the length from the origin to the angle θ is (b/2) × [θ × sqrt(1 + θ²) + asinh(θ)]. For a spiral that starts at a radius r₀, subtract the length of the part below r₀. For 5 turns with a spacing of 0.5 from a radius of 1, the length is about 70.8, close to the mean circumference estimate of 70.7.

Why is the mean circumference a good estimate?

Each turn is nearly a circle, and the radius changes slowly from one turn to the next. The total length is then about π × (r₀ + r_end) × N, the mean circumference times the number of turns. The estimate is very accurate when the spacing is small compared with the radius, as for tape rolls and coils.

Can it be used to measure a roll of material?

Yes. Enter the core radius, the thickness of the material as the spacing between turns, and the number of layers. The length gives the amount of tape, wire, paper or film wound. Thick material or loose winding changes the spacing, so measure the final radius to check the model.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.