Skip to content
Omnikalc

Bimetal strip curvature calculator (Timoshenko): radius, tip deflection and end rotation for a temperature change

Enter the expansion coefficients, the moduli, the thicknesses, the length and the temperature change of a two-layer strip to get its curvature, radius and tip deflection.

Updated on
Your inputs

Value out of range

Value out of range

ksi

Value out of range

ksi

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

°F

Value out of range

Results

Curvature of the strip

0.0142 /in

Radius of curvature
70.3 in
Tip deflection of a cantilever strip
0.0284 in
End rotation of the strip
1.63 °
Total thickness
0.040 in

A bimetal strip bends when the temperature changes, because its two layers expand differently. The bimetal strip calculator uses the Timoshenko formula to give the curvature, the radius of curvature, the tip deflection and the rotation of the end of the strip.

How the calculation works

  • Enter the expansion coefficient and the modulus of the two layers: the one that expands less (layer 1) and the one that expands more (layer 2).
  • Enter the thickness of each layer, the free length of the strip and the temperature change.
  • The calculator applies the Timoshenko formula for the curvature of a bimetal strip, with m = t₁/t₂ and n = E₁/E₂.
  • It gives the curvature, the radius of curvature, the tip deflection of a cantilever strip of the given length and the rotation of its end.

Example

A strip is made of a layer of low-expansion alloy (6.5 × 10⁻⁶ per °F, 29,000 ksi) and a layer of brass-like alloy (10.4 × 10⁻⁶ per °F, 15,000 ksi), each 0.02 in thick, and is 2 in long. A rise of 100 °F gives a curvature of 0.0142 per inch, that is a radius of 70.3 in. A cantilever strip deflects by 0.0284 in at the tip, and its end turns by 1.63°.

Why it matters

The calculator helps engineering students, designers of thermostats and thermal switches, and makers to size a bimetal element, to check how much it moves for a given temperature rise and to compare materials. It gives the response of the strip before building a prototype.

Good to know

The formula is for a strip of two layers bonded perfectly, with a uniform temperature, a linear elastic behavior and a small deflection compared with the length. It does not include the stress limit of the materials, the effect of the temperature on the properties, the load on the strip or the thermal lag. Manufacturers give the flexivity of their alloys, which is more precise.

The thermal expansion calculator gives the free change of length of one material, the Young’s modulus calculator relates stress and strain, the section modulus calculator is used for bending, and the heat conduction calculator shows how fast the strip follows the temperature.

Frequently asked questions

How does a bimetal strip work?

A bimetal strip is made of two metals bonded together, with different thermal expansion coefficients. When the temperature changes, one layer wants to expand more than the other, and because they are bonded together, the strip bends. It is the principle of simple thermostats, circuit breakers, dial thermometers and some fire detectors.

Which formula does the calculator use?

It uses the formula of Timoshenko for the curvature of a bimetal strip: κ = 6 (α₂ − α₁) ΔT (1 + m)² / [h (3 (1 + m)² + (1 + m n)(m² + 1/(m n)))], where m is the ratio of the thicknesses, n the ratio of the moduli and h the total thickness. For equal thicknesses and moduli it reduces to κ = 1.5 (α₂ − α₁) ΔT / h.

How is the tip deflection computed?

For a strip held at one end, with uniform curvature κ, the tip deflection is about κ L² / 2, and the end turns by κ L radians. The estimate is valid for small deflections compared with the length. For a strip supported at its ends, the deflection at the middle is κ L² / 8.

How can I get more movement?

Use materials with a large difference between their expansion coefficients, make the strip thinner, because the curvature is inversely proportional to the thickness, and make it longer, because the deflection grows with the square of the length. The best thickness ratio and modulus ratio depend on the materials, and equal thicknesses are close to the optimum.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.