Skip to content
Omnikalc

Earth curvature and refraction leveling correction calculator

Enter the lengths of the backsight and the foresight and the accepted error to get the curvature and refraction correction, the net error and the longest sight.

Updated on
Your inputs
ft

Value out of range

ft

Value out of range

ft

Value out of range

Results

Net error in the height difference

0.0020 ft

Correction at the backsight
0.0033 ft
Correction at the foresight
0.0013 ft
Longest equal-length sight for the accepted error
697 ft
Net error to accepted error
0.20
The net error is small: the sights are well balanced

The earth curvature and refraction calculator gives the combined correction of the backsight and the foresight of a level, the net error in the height difference, and the longest sight for the error you accept.

How the calculation works

  • Enter the length of the backsight and the length of the foresight.
  • Enter the error you can accept in one setup.
  • The calculator gives the curvature and refraction correction of each sight, the net error and the longest sight for the error you accept.

Example

A level is set up with a backsight of 400 ft and a foresight of 250 ft. The combined correction is 0.0206 K², with K in thousands of feet. At the backsight it is 0.0206 × 0.4² = 0.0033 ft, at the foresight 0.0206 × 0.25² = 0.0013 ft. The net error in the height difference is 0.0020 ft, which is 0.20 of an accepted error of 0.01 ft. With equal sights, the error cancels, and a single sight could be as long as 697 ft before it alone reached 0.01 ft.

Why it matters

The calculator helps surveyors, civil engineers and students to see the size of the curvature and refraction error of a level line, to check the effect of unbalanced sights and to choose the sight lengths for a tolerance.

Good to know

Balance the backsight and the foresight at each setup, and keep the line of sight well above the ground. Where a stream or a road prevents balanced sights, use the correction of the calculator, and run the loop in both directions. Do not forget that the rod readings of a long sight are also affected by the error of the level bubble and the heat shimmer.

The differential leveling misclosure calculator gives the allowable closing error of a loop, the stadia calculator gives distance and elevation from the hairs, the traverse closure calculator checks a closed traverse and the grade stake calculator gives the cut or fill at a stake.

Frequently asked questions

What are curvature and refraction?

A level sight is a straight horizontal line, but the level surface of the earth curves away below it, so a rod read at a distance reads too high by the curvature. The light bends in the atmosphere, which brings the apparent point back toward the level line, by about 14 % of the curvature. The combined effect is a reading that is too high by c = 0.0206 K² in feet, with K in thousands of feet, or 0.0675 K² in meters, with K in kilometers.

Why does it cancel with equal sights?

The correction grows with the square of the distance and it has the same sign for the backsight and the foresight. The height difference is the backsight reading minus the foresight reading, so the two corrections cancel if the sight lengths are equal. That is why level lines are run with balanced sights, with the instrument midway between the two rods. Only the difference between the two corrections is left when the sights are not equal.

How long can a sight be?

For a tolerance of 0.01 ft the combined correction reaches this value at a distance of about 700 ft, and 0.001 ft at about 220 ft. In ordinary leveling the sights are 100 to 300 ft, so the correction is below 0.002 ft and it cancels with balanced sights. Trigonometric leveling and long sights over water or a valley need the correction, and a reciprocal observation reduces the refraction error.

What does the calculator leave out?

The calculator uses the standard coefficient of refraction of 0.14 and does not model the variation of the refraction with the temperature gradient, the time of day or the height of the line above the ground. Refraction can be much larger and not constant near the ground in the sun. Keep the line of sight at least 1.5 to 3 ft above the ground, avoid the heat of the midday, and do not rely on the correction to fix bad conditions.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.