Skip to content
Omnikalc

Carothers equation calculator: how long are the chains of a step-growth polymer?

Enter the extent of reaction, the monomer ratio and the mass of a structural unit to get the degree of polymerization, Mn, Mw and the conversion needed for a target chain length.

Updated on
Your inputs
%

Value out of range

Value out of range

g/mol

Value out of range

Value out of range

Results

Number-average degree of polymerization

50.0

Number-average molar mass Mn

5,650 g/mol

Extent of reaction needed for the target

99.00%

Reachable A realistic conversion for this chain length.
Weight-average molar mass Mw
11,187 g/mol
Dispersity Mw/Mn
1.98
Chain length at full conversion for this ratio
0

In a step-growth polymerization such as the making of nylon or polyester, chains grow by reacting two functional groups at a time. Long chains appear only when almost all the groups have reacted. The Carothers equation links the extent of reaction p to the degree of polymerization Xn, the average number of structural units in a chain. This calculator applies it, including the effect of an imbalance between the two monomers, and gives the molar masses.

How the calculation works

  • Degree of polymerization Xn = (1 + r) ÷ (1 + r − 2rp), with r the stoichiometric ratio (at most 1) and p the extent of reaction
  • For balanced monomers (r = 1): Xn = 1 ÷ (1 − p)
  • Mn = Xn × mass of a structural unit
  • Dispersity Mw ÷ Mn = 1 + p (Flory’s most probable distribution), so Mw = Mn × (1 + p)
  • Conversion for a target Xn: p = (1 + r)(1 − 1 ÷ Xn) ÷ (2r)

Example

At 98 % conversion with balanced monomers, Xn is 50.0. With a structural unit of 113 g/mol, as in nylon 6,6, Mn is 5,650 g/mol and Mw is 11,187 g/mol, a dispersity of 1.98. To reach a degree of polymerization of 100, the conversion must be 99.00 %.

Why it matters

The equation explains why step-growth polymers need very pure monomers and very high conversion. At 90 % conversion, chains average only 10 units, which is a wax and not a plastic. Reaching 99 % gives 100 units. An imbalance in the monomers, or impurities that cap the chain, limits Xn even at full conversion: with r = 0.99, the chain cannot exceed about 199 units. Producers use this deliberately to control the molar mass by adding a small excess of one monomer.

Good to know

The equation assumes equal reactivity of all groups, no side reactions and no cyclization. The dispersity of 1 + p tends to 2 at high conversion, which is the theoretical value for step-growth. In chain-growth polymerization (such as polyethylene or polystyrene), long chains form early and this equation does not apply. For monomers with more than two groups, branching and gelation make the equation invalid near the gel point. Water or other by-products must be removed to push the equilibrium in a condensation reaction.

In practice

Use the tool to see how quickly Xn rises beyond 95 % conversion, and to find how pure a monomer must be. For production, confirm with measured viscosity or chromatography.

Frequently asked questions

What is the Carothers equation?

It is Xn = 1 ÷ (1 − p) for equal amounts of two bifunctional monomers, where p is the extent of reaction. A more general form includes the stoichiometric ratio r.

Why do I need 99 % conversion for a useful polymer?

At 99 % the chains have 100 units on average. At 95 % they have only 20, which is too short for good mechanical properties in most polymers.

How does a monomer imbalance affect the chain length?

It caps Xn at (1 + r) ÷ (1 − r) even at full conversion. With r = 0.98, the maximum is 99 units.

Does it apply to polyethylene?

No. Polyethylene and polystyrene grow by chain-growth, where each chain forms quickly. The Carothers equation is for step-growth polymers, such as polyamides, polyesters and polyurethanes.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.