Skip to content
Omnikalc

Ergun equation calculator: how much pressure does a packed bed use?

Enter the velocity, the bed length, the particle size, the void fraction and the fluid properties to get the pressure drop of a packed bed with the Ergun equation.

Updated on
Your inputs
ft/s

Value out of range

ft

Value out of range

in

Value out of range

Value out of range

lb/ft³

Value out of range

cP

Value out of range

Results

Pressure drop across the bed

13.48 psi

Pressure drop per foot of bed
2.247 psi/ft
Particle Reynolds number
484
A transition regime: both the viscous and the inertial terms count
Share of the pressure drop from viscous forces
15.1 %

When a liquid or gas flows through a bed of packing, catalyst or sand, it loses pressure by friction against the particles. The Ergun equation calculator takes the superficial velocity, the bed length, the particle diameter, the void fraction, and the density and viscosity of the fluid, and gives the pressure drop over the bed and per foot, the particle Reynolds number and the share of the loss due to viscous forces.

How the calculation works

  • Enter the superficial velocity of the fluid (the flow rate divided by the empty cross-section), the bed length, the particle diameter, the void fraction ε of the bed, and the density and viscosity of the fluid.
  • The calculator applies the Ergun equation: ΔP / L = 150 μ (1 − ε)² u / (ε³ d²) + 1.75 ρ (1 − ε) u² / (ε³ d).
  • The first term is the viscous loss (Blake–Kozeny), which dominates at low flow, and the second is the inertial loss (Burke–Plummer), which dominates at high flow.
  • It gives the pressure drop over the whole bed and per foot, the particle Reynolds number and the share of viscous loss.

Example

Water flows at 0.3 ft/s through a bed 6 ft long of 1/8 in spheres with a void fraction of 0.4. The viscous term gives 7,654 Pa/m and the inertial term 43,186 Pa/m. The pressure drop is 50,840 Pa/m, which is 2.25 psi/ft, or 13.5 psi over the bed. The particle Reynolds number is 484, a transition regime, and 15 % of the loss comes from viscous forces.

Why it matters

The pressure drop of a packed bed sets the size of pumps and blowers and the energy cost of a process. Chemical engineers use the Ergun equation for fixed-bed reactors, absorption and distillation columns, filters and ion exchangers, and the calculator shows which part of the loss, viscous or inertial, matters for a given flow.

Good to know

The equation is for a uniform bed of particles of the same size, with a constant void fraction, and a fluid that does not change density (liquids, and gases with a small drop in pressure). In gases with a large pressure drop, the velocity changes along the bed. Wall effects increase the void fraction near the wall in narrow columns, and particle shape and size distribution change the result. The constants 150 and 1.75 are typical and vary for real beds.

The Reynolds number calculator characterises the type of flow, the NPSH calculator covers the suction of pumps, the residence time calculator covers the time in a vessel, and the Darcy’s law calculator covers flow in porous media.

Frequently asked questions

What is the Ergun equation?

It is the most used equation for the pressure drop of a fluid through a bed of particles, found by Sabri Ergun in 1952. It adds the Blake–Kozeny equation for laminar flow, in which the loss is proportional to the velocity, and the Burke–Plummer equation for turbulent flow, in which it is proportional to the square of the velocity. It holds for the whole range of flow.

Why does the void fraction matter so much?

The pressure drop depends on the void fraction ε through the factors (1 − ε)² / ε³ and (1 − ε) / ε³. A change in ε from 0.40 to 0.35 raises the drop by about 70 %. This is why the way a bed is packed, and the way it settles in use, changes the pressure drop of a column, and why a non-uniform bed lets the fluid take the path of least resistance.

What particle diameter should I use for non-spherical particles?

Use the equivalent sphere diameter times the sphericity, dp = Φs × d_volume-equivalent, which is the diameter of a sphere with the same surface-to-volume ratio as the particle. For cylinders, rings and irregular grains, the sphericity is below 1 (for example, 0.8 to 0.9 for crushed rock). Using the nominal size would underestimate the pressure drop.

What can the pressure drop be used for?

The result is used to size the pump or the blower of a packed column, a filter bed, a catalyst reactor, an adsorption column or a sand filter, and to check that the bed is not lifted or fluidised by the flow. When the pressure drop equals the weight of the bed per unit area, the bed starts to fluidise, which the fluidisation velocity calculator covers.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.