Skip to content
Omnikalc

Extension spring calculator: spring rate, force with initial tension, shear stress and stored energy

Enter the wire, the coil diameter, the active coils, the modulus, the initial tension and the extension to get the rate, the force, the shear stress and the stored energy.

Updated on
Your inputs
in

Value out of range

in

Value out of range

Value out of range

psi

Value out of range

lbf

Value out of range

in

Value out of range

psi

Value out of range

Results

Force at the extension

15.74 lbf

Spring rate
8.50 lbf/in
Shear stress in the body (with Wahl factor)
99,458 psi
Stress as a share of the tensile strength
36.8 %
Within the usual 45 % guideline for the body of the spring
Energy stored from the free length
14.06 lbf·in

An extension spring pulls when it is stretched and has an initial tension that holds the coils closed. The extension spring calculator gives the spring rate, the force at a given extension, the shear stress with the Wahl factor, its share of the tensile strength and the energy stored.

How the calculation works

  • Enter the wire diameter, the mean coil diameter and the number of active coils of the extension spring.
  • Enter the shear modulus of the wire (about 11.5 million psi for music wire) and the initial tension that holds the coils together.
  • Enter the extension from the free length, and the tensile strength of the wire.
  • The calculator gives the rate k = G d⁴ / (8 D³ N), the force F = Fᵢ + k x, the shear stress with the Wahl factor and its share of the tensile strength, and the energy stored.

Example

An extension spring has a wire diameter of 0.062 in, a mean coil diameter of 0.5 in, 20 active coils, a shear modulus of 11,500,000 psi and an initial tension of 3 lbf. The rate is 8.50 lbf/in. Extended by 1.5 in, the force is 3 + 8.50 × 1.5 = 15.74 lbf. With the Wahl factor of 1.182, the shear stress is 99,458 psi, which is 36.8 % of a 270,000 psi tensile strength. The energy stored is 14.06 lbf·in.

Why it matters

The calculator helps designers of latches, doors, trampolines, garage mechanisms, toys and tools, engineering students and makers to choose a spring, to know the force at the working length and to check if the wire is overloaded. It saves time before comparing catalogue springs, because it shows the effect of the wire diameter, the coil diameter and the number of coils.

Good to know

The calculation is for the body of the spring and the elastic range. The hooks, the fatigue life, the loss of initial tension with time and the effect of the temperature are not included. The 45 % guideline for the stress is a common value for static loads on music wire, and cyclic loads need a lower stress. The extension should also stay under the maximum length given by the manufacturer, so that the spring is not deformed.

The compression spring calculator handles pushing springs, Hooke’s law gives the force of an ideal spring, the spring-mass calculator gives the oscillation of a spring and a weight, and the Young’s modulus calculator handles the stiffness of materials.

Frequently asked questions

What is the initial tension of an extension spring?

Extension springs are wound with the coils pressed together, and the winding leaves a force that holds the coils closed. This initial tension must be exceeded before the spring starts to extend. The force at an extension x is the initial tension plus the rate times x, so the line of force against extension does not start at zero but at the initial tension.

How is the rate of the spring computed?

The coils of an extension spring are loaded in torsion, like those of a compression spring. The rate is G d⁴ / (8 D³ N), where G is the shear modulus, d the wire diameter, D the mean coil diameter and N the number of active coils. Doubling the number of coils halves the rate, and doubling the wire diameter multiplies it by 16.

What is the Wahl factor?

The Wahl factor corrects the shear stress for the curvature of the wire and for the direct shear. It is Kw = (4C − 1) / (4C − 4) + 0.615 / C, where C = D / d is the spring index. For an index of 8 it is near 1.18, so the real stress is 18 % higher than the simple torsion formula gives.

Why is the stress at the hooks not given?

The hooks carry bending and torsion stresses that are higher than those of the body, and they are usually the place where an extension spring breaks. A hook with a small bend radius can have a stress concentration of 2 or more. The calculator checks only the body, so the design of the hooks must be reviewed separately, with a larger radius or with a stronger design.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.