Skip to content
Omnikalc

Torsion spring calculator: rate, torque at an angle and bending stress of a helical torsion spring

Enter the wire diameter, the coil diameter, the active coils, the modulus, the angle and the tensile strength to get the spring rate, the torque and the bending stress.

Updated on
Your inputs
in

Value out of range

in

Value out of range

Value out of range

psi

Value out of range

°

Value out of range

psi

Value out of range

Results

Torque at the deflection angle

6.37 lb·in

Spring rate per degree
0.0707 lb·in/°
Bending stress in the wire (with curvature factor)
137,607 psi
Stress as a share of the tensile strength
51.0 %
Within about 78 % of the tensile strength, a common static limit
Turns of deflection
0.250

A torsion spring stores energy when its arms are rotated, as in a clothespin, a mousetrap or a hinge. The torsion spring calculator gives the torque at a given angle, the spring rate per degree, the bending stress in the wire and the share of the tensile strength used.

How the calculation works

  • Enter the wire diameter, the mean coil diameter and the number of active coils of the helical torsion spring.
  • Enter the modulus of elasticity of the wire (about 28.5 million psi for music wire) and the angle through which the spring is wound.
  • Enter the tensile strength of the wire to see how highly the spring is stressed.
  • The calculator gives the spring rate k = E d⁴ / (64 D N) per radian, converted to degrees, the torque at the angle, the bending stress with the curvature factor Kᵢ = (4C² − C − 1) / (4C (C − 1)) and the stress as a share of the tensile strength.

Example

A music wire torsion spring has a wire diameter of 0.080 in, a mean coil diameter of 0.75 in, 6 active coils and a modulus of 28,500,000 psi. Its rate is 4.053 lb·in per radian, or 0.0707 lb·in per degree. Wound by 90° it gives a torque of 6.37 lb·in. The spring index is 9.375 and the curvature factor is 1.086, so the bending stress is 137,607 psi. With a tensile strength of 270,000 psi, that is 51.0 %, and the spring is wound by 0.25 turn.

Why it matters

The calculator helps designers of hinges, latches, clips, toys and small mechanisms, engineering students and makers to choose the wire and the coil size, to find the torque at an angle and to see if the wire is overstressed before ordering or winding a spring. It gives a first check before the detailed design with a spring manufacturer.

Good to know

The rate formula uses the theoretical value 64 in the denominator. Friction against the arbor and the arms changes the measured rate, and many designers use a test-based value of 10.8 instead of 10.19 in the rate per turn formula, which lowers the rate by about 6 %. The calculator does not include the effect of the arms, the reduction of the coil diameter under load or the fatigue life, and the spring should be tested before it is used in a safety-critical device.

The compression spring calculator handles axial springs, the spring-mass calculator gives the oscillation of a spring and a weight, the shaft torsion calculator handles twist in shafts, and the torque calculator relates force and distance.

Frequently asked questions

How is the rate of a torsion spring computed?

A helical torsion spring is loaded in bending, like a coiled beam. Its rate per radian is E d⁴ / (64 D N), where E is the modulus of elasticity, d the wire diameter, D the mean coil diameter and N the number of active coils. Dividing by 57.3 gives the rate per degree. The torque is the rate multiplied by the angle of deflection.

What is the curvature factor?

The inner side of a coiled wire carries more stress than a straight beam. The curvature factor Kᵢ corrects the bending stress for this effect. It depends on the spring index C = D / d, and it is greater for small indexes. For an index of about 9 it is near 1.09, so the stress is 9 % higher than the simple beam formula gives.

What is the maximum stress allowed?

For static loads the bending stress is often kept under about 78 % of the tensile strength of music wire or hard-drawn wire, and a bit less for other materials. For springs that are wound and released millions of times, the limit is much lower, and the fatigue limit must be checked with the stress range and the surface finish.

Should a torsion spring be wound in the direction of the coils?

Yes. The spring must be loaded in the direction that tightens the coils, which reduces the stress at the inner side and raises the allowed torque. Loading in the opposite direction opens the coils and can increase the stress, so the design should avoid this. The coil diameter also gets smaller when the spring is wound, so leave room around the pin.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.