Skip to content
Omnikalc

Fox equation calculator: how much does a plasticizer or a second polymer lower the glass transition?

Enter the glass transition of two components and the weight fraction of the polymer to get the glass transition of the blend and the composition needed for a target temperature.

Updated on
Your inputs
°C

Value out of range

°C

Value out of range

%

Value out of range

°C

Value out of range

Results

Glass transition of the blend

54.3 °C

Glassy at room temperature Hard and rigid at 20 °C.

Polymer fraction needed to reach the target

65.3%

Reachable A blend of this composition reaches the target.
Lowering compared with the pure polymer
50.7 K
Second component needed to reach the target
34.7%
Drop in glass transition per 1 % of second component here
2.18 K

The glass transition temperature (Tg) is the point where a polymer changes from hard and glassy to soft and rubbery. Many practical materials are mixtures: a polymer and a plasticizer, a blend of two compatible polymers or a copolymer. The Fox equation predicts the Tg of such a mixture from the Tg of each component and its weight fraction. This calculator applies it, and also solves it the other way round to find the composition for a target Tg.

How the calculation works

  • Fox equation: 1 ÷ Tg = w₁ ÷ Tg₁ + w₂ ÷ Tg₂, with temperatures in kelvin and w the weight fractions (w₂ = 1 − w₁)
  • Composition for a target Tg: w₁ = (1 ÷ Tg − 1 ÷ Tg₂) ÷ (1 ÷ Tg₁ − 1 ÷ Tg₂)
  • Lowering = Tg₁ − Tg of the blend

Example

A polymer with a Tg of 105 °C is mixed at 80 % by weight with a plasticizer whose Tg is -60 °C. The blend has a Tg of 54.3 °C, which is 50.7 K below the pure polymer. To bring the Tg to 25 °C, the mixture must contain 65.3 % polymer and 34.7 % of the second component. Near this composition, each additional 1 % of the second component lowers the Tg by about 2.18 K.

Why it matters

Plasticizers make PVC flexible, and in coatings, adhesives and drug films the Tg sets whether the material is brittle or tacky at the use temperature. In a polymer for a pharmaceutical dispersion, moisture acts as a plasticizer, so a small amount of water can lower the Tg by tens of degrees and make a stable solid soft. The Fox equation lets you estimate this quickly before running experiments.

Good to know

The equation assumes ideal mixing, with no specific interactions and the same heat capacity change at the transition for both components. It works best for miscible blends and random copolymers of similar monomers. Strong interactions such as hydrogen bonding can make the real Tg higher or lower than the prediction. The Gordon-Taylor equation adds an adjustable constant for such cases. Use the Tg values measured by the same method, usually by differential scanning calorimetry, and use weight fractions, not mole fractions.

In practice

Use the result as a guide to choose how much plasticizer to test, then measure the blend. Include water if the material absorbs moisture. This tool is for estimation.

Frequently asked questions

What is the Fox equation?

It is 1/Tg = w1/Tg1 + w2/Tg2, with temperatures in kelvin. It gives the glass transition of a miscible mixture from its components.

Does it work for plasticized PVC?

It gives the right trend: more plasticizer lowers the Tg. For quantitative design, check with measurements, because real systems often deviate.

Why use kelvin?

The equation involves reciprocal temperatures, which only make sense on an absolute scale. The calculator converts from Celsius for you.

How does water affect the Tg?

Water has a very low Tg, around -135 °C, so even a few percent can lower the Tg of a hydrophilic polymer by many degrees.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.