Skip to content
Omnikalc

Hypsometric equation calculator: how thick is the air between two pressure levels?

Enter the mean temperature of a layer and the pressures at its bottom and top to get the thickness, the scale height and the equivalent 1000–500 mb thickness.

Updated on
Your inputs
°F

Value out of range

mb

Value out of range

mb

Value out of range

Results

Thickness of the layer

9,185 ft

Thickness of the layer in metres
2,800 m
Scale height of the atmosphere
7.85 km
Equivalent 1000–500 mb thickness
5,441 m
Borderline: a rain–snow mix is likely

Warm air is lighter than cold air, so a layer of warm air between two pressure levels is thicker than a layer of cold air. The hypsometric equation calculator takes the mean temperature of a layer and the pressures at its bottom and top, and gives the thickness of the layer in feet and metres, the scale height of the atmosphere and the equivalent 1000–500 mb thickness with a rain–snow indication.

How the calculation works

  • Enter the mean temperature of the air layer, the pressure at the bottom and the pressure at the top of the layer.
  • The calculator applies the hypsometric equation: Δz = (R T / g) × ln(p₁ / p₂), with R = 287.05 J/(kg·K) for dry air and g = 9.80665 m/s².
  • The result is the thickness of the layer, the distance in height between the two pressure surfaces. A warmer layer is thicker, because warm air is less dense.
  • It also gives the scale height R T / g, and the equivalent 1000–500 mb thickness for the same mean temperature, which forecasters compare with the 5,400 m line that separates snow from rain.

Example

A layer with a mean temperature of 23 °F (−5 °C, 268.15 K) between 1,000 mb and 700 mb has a scale height of 287.05 × 268.15 / 9.80665 = 7.849 km. Its thickness is 7,849 × ln(1,000 / 700) = 2,799.5 m, which is 9,185 ft. The equivalent 1000–500 mb thickness is 7,849 × ln 2 = 5,441 m, close to the rain–snow line, so a mix is likely.

Why it matters

The hypsometric equation is a basic relation of meteorology and altimetry. It is used in weather maps to read the temperature of a column from the height of pressure surfaces, to forecast the type of winter precipitation, and to calibrate the barometric altimeters of aircraft and drones. It also helps students to see how pressure, temperature and height are linked.

Good to know

The equation assumes dry air in hydrostatic balance and a mean temperature that represents the whole layer. Water vapour makes the air a little lighter, and a virtual temperature would correct this by up to a few metres per kilometre. The 5,400 m rule is only a guide for the middle latitudes. Do not use it alone to decide whether it will snow.

The barometric pressure calculator links pressure to altitude, the density altitude calculator shows how thin the air is, the dew point calculator gives the condensation temperature, and the cloud base calculator estimates the height of the clouds.

Frequently asked questions

What is the hypsometric equation?

It links the thickness of an air layer between two pressure levels to the mean temperature of the layer: Δz = (R T / g) ln(p₁ / p₂). It follows from the hydrostatic balance and the ideal gas law. It shows that warm air layers are thicker, which is why the height of a pressure surface is a good measure of the temperature below it.

What is the 5,400 m rule?

In winter forecasting, the thickness between 1000 and 500 hPa is compared with 5,400 m (540 dam). Lower values indicate a cold column in which precipitation falls as snow, higher values a warm column with rain, and a range around 5,400 to 5,460 m often means a mix. It is a rule of thumb, valid mainly for the middle latitudes, and local conditions can differ.

What is the scale height?

The scale height H = R T / g is the height over which the pressure falls by a factor of e (about 2.718) in an isothermal atmosphere. It is about 8 km at 0 °C, and it is larger in warm air. The thickness between two pressure levels is simply H times the logarithm of their ratio.

Can I use it to compute altitude from pressure?

Yes, as long as you use a good mean temperature for the layer. This is the basis of the barometric altimeter. With the temperature of the ground only, the answer is a bit off, since temperature falls with height. Use the mean of the temperatures at the bottom and the top of the layer for a better result.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.