Skip to content
Omnikalc

Ice thickness calculator: how thick can lake ice grow in a cold spell?

Enter the freezing degree-days, the starting thickness and the site conditions to estimate the ice thickness with Stefan’s law. An estimate only: always measure the ice.

Updated on
Your inputs
°F-days

Value out of range

in

Value out of range

Results

Estimated ice thickness

8.2 in

An estimate only: always measure the ice before going out
Estimated ice thickness in centimetres
20.9 cm
Thickness without the site factor (Stefan, ideal)
10.3 in
Growth since the start
6.2 in

Ice on a lake grows as the cold removes the heat of the water below it, and the thicker it gets, the more slowly it grows. The ice thickness calculator applies Stefan’s law to the freezing degree-days, the starting thickness and the site conditions, and gives the estimated ice thickness in inches and centimetres, the ideal thickness with no site factor and the growth since the start. It is an estimate only, and the ice must always be measured before anyone goes on it.

How the calculation works

  • Enter the freezing degree-days accumulated since the freeze-up, the ice thickness at the start and the site conditions.
  • Freezing degree-days add up how far each day’s average temperature is below freezing. Four days at 25 °F, for example, give 4 × 7 = 28 °F-days.
  • The calculator applies Stefan’s law, based on the heat conduction through the ice: h² = h₀² + 2 k × FDD × 86,400 / (ρ L), with k = 2.1 W/(m·K), ρ = 917 kg/m³ and L = 334 kJ/kg.
  • The result is then multiplied by a site factor of 1.0, 0.8 or 0.6, since snow cover and currents slow the growth. Always measure the ice before using it.

Example

A lake starts the cold season with 2 in of ice (5.08 cm). After 100 °F-days (55.6 °C-days), the ideal Stefan thickness is 10.3 in. With the factor of 0.8 for an average lake with some snow, the estimate is 8.2 in (20.9 cm), a growth of 6.2 in. This is only an estimate, and the ice has to be measured with a drill or an auger before anyone walks on it.

Why it matters

Anglers, skaters, snowmobilers and ice-road builders want to know when a lake will have enough ice, and the calculation shows how the cold of the past weeks adds up. It also teaches the physics of freezing, with its square-root law. As a planning tool it tells you when to start checking, and not whether the ice is safe.

Good to know

Stefan’s law is a simplified model of ice growing from a water surface at freezing point, with a constant conductivity and no heat from the water. It ignores snow, wind, currents, solar heating and flooding. It can be wrong by a lot, in both directions. Never rely on a calculation for safety: measure the ice in many places, read the local ice reports, and carry rescue equipment.

The heating degree days calculator accumulates cold in the same way, the heat conduction calculator covers the heat flow through a layer, the latent heat calculator covers the heat of freezing, and the wind chill calculator turns wind and cold into a felt temperature.

Frequently asked questions

Can I use this to decide if the ice is safe?

No. The result is a rough estimate of growth, and ice safety depends on many factors the calculator cannot see: currents, springs, inflows, pressure ridges, cracks, old ice, slush layers and the type of ice. Check the thickness with an ice auger or drill at several places, check local advice, and never go out alone. Even thick ice can be unsafe.

What are freezing degree-days?

For each day, you take the number of degrees by which the average temperature is below the freezing point (32 °F or 0 °C), and you add them up since the start of the freeze. Colder and longer spells give more degree-days and more ice. Weather services and lake monitoring sites often publish the accumulated value for a region.

Why does the growth slow down?

The ice itself is an insulator, and the heat of the water has to cross the layer already formed in order to escape. Because of this, the thickness grows with the square root of the degree-days and not in a straight line. The first inch forms quickly, and each next inch takes longer.

What does the site factor do?

Snow is a much better insulator than ice, so a snow cover can cut the growth by a third or more. Flowing water, wind and springs also slow the growth. The factor of 1.0 is for clear ice on a calm lake, 0.8 for average conditions and 0.6 for snowy lakes or rivers. These values are rough and the real factor must be tested on the site.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.