Skip to content
Omnikalc

Ionic strength calculator: how crowded with charge is your solution?

Choose a salt, its concentration and an ion charge to get the ionic strength, the activity coefficients from the limiting law, the Güntelberg and Davies equations, and the Debye length.

Updated on
Your inputs
mol/L

Value out of range

Results

Ionic strength

0.3000 mol/L

Within the range of the Davies equation (up to 0.5 mol/L)
Activity coefficient, Debye–Hückel limiting law
0.0767
Activity coefficient, extended (Güntelberg) equation
0.1903
Activity coefficient, Davies equation
0.2902
Debye length at 25 °C
0.555 nm

In a solution of salt, ions interact and behave as if they were less concentrated. The ionic strength calculator gives the ionic strength of a solution of a common salt from its concentration, and the activity coefficient of an ion by three equations: the Debye–Hückel limiting law, the Güntelberg equation and the Davies equation. It also gives the Debye length.

How the calculation works

  • Choose the dissolved salt. The calculator knows how many ions of each charge it releases.
  • Enter the concentration of the salt in mol/L and the charge of the ion whose activity you want.
  • The ionic strength is I = ½ Σ cᵢ zᵢ², summed over all the ions in the solution.
  • The activity coefficient γ comes from the Debye–Hückel limiting law, the Güntelberg equation or the Davies equation: log γ = −0.509 z² (√I / (1 + √I) − 0.3 I).

Example

A 0.1 mol/L solution of calcium chloride gives 0.1 mol/L of Ca²⁺ and 0.2 mol/L of Cl⁻. The ionic strength is ½ (0.1 × 4 + 0.2 × 1) = 0.3 mol/L. For the Ca²⁺ ion (z = 2), the Davies equation gives γ = 0.2902, so the ion behaves as if its concentration were only 29 % of the real one. The Debye length is 0.555 nm.

Why it matters

The ionic strength sets the activity coefficients that are needed to compute accurate pH values, solubilities, equilibrium constants and electrode potentials in water. It is used in analytical chemistry, in water treatment, in geochemistry, in biochemistry for buffers and in colloid science.

Good to know

The calculator treats the salt as fully dissociated and the only source of ions, in water at 25 °C. It ignores ion pairing, which is important for 2:2 salts such as magnesium sulfate, where part of the ions form neutral pairs, and the other ions of a buffer or of the medium, which add to the ionic strength. The Debye length formula 0.304/√I nm is for a 1:1 electrolyte in water, and the values for 2:1 and higher charges are approximate.

The Debye length calculator gives the screening length from the permittivity and the concentration, the molarity calculator converts the amount of salt to concentration, the solubility product calculator uses the activities, and the normality calculator gives the equivalents of the ions.

Frequently asked questions

What is the ionic strength?

It is a measure of the total concentration of ions in a solution that takes their charges into account: I = ½ Σ cᵢ zᵢ². Ions of higher charge count for much more, since the charge is squared. A 0.1 mol/L solution of NaCl has I = 0.1 mol/L, but 0.1 mol/L of MgSO₄ has I = 0.4 mol/L.

What is an activity coefficient?

In a real solution, ions attract and repel each other, so they do not behave as in an ideal solution. The activity a = γ c is the effective concentration, and γ is the activity coefficient. It is 1 in a very dilute solution and falls when the ionic strength rises. Equilibrium constants, solubility products and electrode potentials are written with activities, not with concentrations.

Which equation should I use?

The Debye–Hückel limiting law is valid only below about 0.005 mol/L. The extended or Güntelberg equation extends it to about 0.1 mol/L. The Davies equation, with its correction term −0.3 I, is accurate to a few percent up to about 0.5 mol/L. Above that, the activity coefficient rises again for many salts, and specific models such as Pitzer’s are needed.

What is the effect of ionic strength on a reaction or a solubility?

A salt that is more soluble in the presence of other salts is the salting-in effect: the activity coefficients of its ions fall, so more of it must dissolve to reach the same activity product. This is why gypsum is more soluble in seawater than in pure water, and why the rate of reactions between ions depends on the ionic strength, as described by the Brønsted–Bjerrum equation.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.