Skip to content
Omnikalc

Larson-Miller parameter calculator: how much life do you lose when the metal runs hotter?

Enter the temperature, the rupture life and the constant C to get the Larson-Miller parameter and the creep rupture life at another temperature.

Updated on
Your inputs
°F

Value out of range

h

Value out of range

Value out of range

°F

Value out of range

Results

Larson-Miller parameter

38,992

Rupture life at the new temperature
16,728 h
Life at the new temperature, in years
1.91 y
New life as a share of the original life
16.7 %
Temperature for a 1,000-hour life at the same stress
1,236 °F

Metal that carries a load at high temperature slowly stretches, a process called creep, and it eventually breaks. The Larson-Miller calculator takes the service temperature, the rupture life, the constant C and a new temperature, and gives the Larson-Miller parameter, the life at the new temperature in hours and years, its share of the original life and the temperature for a 1,000-hour life at the same stress.

How the calculation works

  • Enter the service temperature and the rupture life known for the alloy at that temperature and stress, and the constant C, usually 20 for steels.
  • The calculator turns the temperature into an absolute scale (Rankine, °F + 459.67) and computes LMP = T × (C + log₁₀ t).
  • Enter a new temperature. Because the parameter is constant for a given stress, the new life is t = 10^(LMP / T − C).
  • Read the new life in hours and years, as a share of the original life, and the temperature that would give a life of 1,000 hours at the same stress.

Example

An alloy is rated for 100,000 hours at 1,100 °F, or 1,559.67 °R. With C = 20, the parameter is 1,559.67 × (20 + 5) = 38,992. At 1,150 °F (1,609.67 °R), the life becomes 10^(38,992 / 1,609.67 − 20) = 10^4.223, or about 16,728 hours. That is 1.9 years instead of 11.4 years, only 16.7 % of the original life, for a rise of just 50 °F. The same stress would give a life of 1,000 hours at about 1,236 °F.

Why it matters

Creep tests that last 100,000 hours are impractical, so engineers run shorter tests at higher temperatures and use the Larson-Miller parameter to trade temperature for time. The same idea lets you see how much life an overheated boiler tube, steam pipe or turbine part has lost, and how much a small drop in temperature can gain.

Good to know

The calculator assumes a constant C and a single master curve at one stress. Real alloys have scatter, several creep mechanisms and a change of slope at long times. It uses the temperature as given, so check that you enter the metal temperature, not the gas temperature. Treat the result as an estimate and not as a substitute for rupture data or for code design rules.

The thermal expansion calculator covers length changes with temperature, the pressure vessel stress calculator gives wall stresses, the Brinell hardness calculator relates hardness to strength, and the principal stress calculator finds the main stresses at a point.

Frequently asked questions

What is the Larson-Miller parameter?

It is a number that combines temperature and time to creep rupture into a single master curve for a given alloy and stress. Frank Larson and James Miller proposed it in 1952. The formula is LMP = T × (C + log₁₀ t), with T on an absolute scale and t in hours. Two combinations of temperature and time with the same parameter give the same rupture stress.

What value should I use for C?

A value of 20 fits most carbon steels, low-alloy steels and stainless steels, and it is the usual default. Some alloys and some data sets fit better with a different C, from about 15 to 25. When you have rupture tests for the material, fit C to those tests and use the fitted value, because the answer is sensitive to it.

Why is the temperature so important?

Creep is thermally activated, so life falls very fast as temperature rises. In the example, 50 °F more cuts the life by more than 80 %. A boiler tube, a turbine blade or a furnace part that runs 50 °F above its design temperature can wear out in a fraction of its planned life.

Can I use it for any temperature and stress?

No. The parameter holds along a master curve at one stress level, and it works only in the range where the creep mechanism stays the same. Extrapolating far beyond the tested times, or from a different stress, can give unsafe numbers. Use it as a quick screening tool and rely on the code allowable stresses for design.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.