Skip to content
Omnikalc

What are the principal stresses at your point?

Enter the normal and shear stresses on a plane: get the principal stresses, their angle, the maximum shear, the von Mises stress and the safety factor.

Updated on
Your inputs

Value out of range

Value out of range

Value out of range

Value out of range

Results

Maximum principal stress σ1

92.43 MPa

Minimum principal stress σ2

7.57 MPa

Angle from the x axis to the σ1 plane
22.50 °
Maximum in-plane shear stress (radius of Mohr's circle)
42.43 MPa
Von Mises equivalent stress
88.88 MPa
Safety factor against yielding
2.81
Safety factor above 2: a comfortable margin

When a part is loaded, the stress at a point depends on the direction in which you look. Principal stresses are the extreme normal stresses, found on the planes where the shear stress vanishes. This calculator takes a plane-stress state (σx, σy and τxy) and gives the principal stresses, the angle of their planes, the maximum in-plane shear, the von Mises equivalent stress and the safety factor against yielding. It is the calculation behind Mohr’s circle.

How the calculation works

  • Average stress = (σx + σy) ÷ 2
  • Radius of Mohr’s circle R = √(((σx − σy) ÷ 2)² + τxy²), which is the maximum in-plane shear
  • Principal stresses σ1,2 = average ± R
  • Angle of the σ1 plane: tan 2θ = 2τxy ÷ (σx − σy)
  • Von Mises = √(σ1² − σ1σ2 + σ2²), and safety factor = yield strength ÷ von Mises

Example

A point in a steel bracket sees σx = 80 MPa, σy = 20 MPa and τxy = 30 MPa. The average stress is 50 MPa and the radius of Mohr’s circle is 42.43 MPa. The principal stresses are 92.43 MPa and 7.57 MPa, on planes turned by 22.5°. The von Mises stress is 88.9 MPa; with a yield strength of 250 MPa, the safety factor is 2.81.

When to use it

Engineers use principal stresses to check shafts, brackets, welds and pressure parts, where several loads act together. Strain gauge rosettes give strains in three directions, and converting them to stresses leads to the same calculation. In soil and rock mechanics, the same circle describes failure planes. The von Mises criterion is the most common test for ductile metals.

Good to know

The sign convention matters: tension is positive and compression is negative, and the shear stress sign follows the usual engineering convention. The calculation covers plane stress only, so thick parts and triaxial states need a full 3D analysis. Stress concentrations at holes and notches can raise the local stress well above the nominal value. A safety factor of 1.5 to 2 is common for static loads, and more for fatigue or uncertain loads.

For the stress in a bending beam, use the beam deflection calculator. For small strains, try the strain gauge calculator, and for a spring or a bar in tension, Hooke’s law.

Frequently asked questions

What are principal stresses?

The largest and smallest normal stresses at a point, found on the planes where the shear stress is zero. The failure of a material is often judged from them.

What is Mohr's circle?

A diagram that shows how the normal and shear stresses change as you rotate the plane. Its center is the average normal stress and its radius is the maximum in-plane shear stress.

What is the von Mises stress?

A single equivalent stress that combines all the stress components. A ductile metal starts to yield when the von Mises stress reaches its yield strength.

Does this give the absolute maximum shear stress?

No. It gives the in-plane value. In a 3D state of stress the absolute maximum shear is half the difference between the largest and smallest principal stresses, including the zero stress through the thickness.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.