Skip to content
Omnikalc

Linear actuator force calculator: how much force to lift a lid?

Enter the weight and length of the lid, the mount position and angle, the safety factor and the number of actuators to get the lid torque, the force needed and the rating of each actuator.

Updated on
Your inputs

Value out of range

Value out of range

Value out of range

°

Value out of range

°

Value out of range

Results

Force needed in total

84.9 lbf

Rated force per actuator

63.6 lbf

Torque of the lid about the hinge
60.0 lb·ft

Hatches, lids, tool box covers, boat seats and doors are often lifted by electric linear actuators or gas struts. Their rating must be right: too weak and the lid stalls, too strong and it is expensive. This linear actuator force calculator takes the weight and length of the lid, the mount position and angle, the safety factor and the number of actuators to give the lid torque, the total force needed and the rated force per actuator.

How the calculation works

  • Weight = mass × 9.81. A uniform lid has its center of gravity at half of its length, so the weight acts at L ÷ 2 from the hinge.
  • Torque of the lid = weight × (L ÷ 2) × cos(angle above horizontal). It is largest when the lid is flat, at 0°.
  • Force needed = lid torque ÷ (distance of the mount from the hinge × sin of the angle between the actuator and the lid). A steeper mount angle gives more lift per pound of force.
  • Rated force per actuator = force needed × safety factor ÷ number of actuators.

Example

A 40 lb hatch is 36 in long, with the actuator mounted 12 in from the hinge at 45° to the lid. The lid is flat at the start. The torque is 40 × 1.5 ft = 60 lb·ft. The force needed is 720 lb·in ÷ (12 in × sin 45°) = 84.9 lbf. With a safety factor of 1.5 and 2 actuators each rated for 63.6 lbf is enough.

Why it matters

The actuator force is a common unknown in builds for camper vans, boats, trailers, workshop covers and home automation. A catalogue lists actuators by force, and the lever geometry decides which is needed. The calculation also shows how changing the mount position by a few inches makes the difference between a small and a large actuator.

Good to know

The model treats the lid as a uniform board with its weight in the middle and ignores friction, the weight of the actuator, wind, snow and the extra load of equipment on the lid. If the weight is unevenly spread, use the real distance to the center of gravity in place of half of the length. The angle between the actuator and the lid changes as it extends, and the force can be much higher at the start, so check the closed position with the true geometry. Select an actuator whose rated force is above the result with a margin and check its duty cycle.

The torque calculator gives the turning force at a hinge, the lever calculator solves lever balance and the force calculator applies Newton’s second law.

Frequently asked questions

How do I size a linear actuator for a hatch or lid?

Find the torque that the lid's weight puts on the hinge, then divide it by the distance from the hinge to the actuator mount, corrected for the angle at which the actuator pushes. Multiply by a safety factor and share the result between the actuators.

Where should the actuator be mounted?

The nearer the mount is to the hinge, the more force the actuator must have and the shorter the stroke needed. A mount farther out gives lower force and more stroke. Mounting at about 90° to the lid, as far as the geometry allows, uses the force best.

Why is the lid hardest to lift when it is closed?

A flat lid has the full weight acting at the longest horizontal distance from the hinge. As it rises, the horizontal distance shrinks with the cosine of the angle, and so does the torque. The actuator angle also changes through the stroke, so check the worst case.

What safety factor should I use?

1.25 to 1.5 covers a clean lift of a known load. Use 2 or more for outdoor use, wind or snow loads, friction in the hinge or a lid that can be pushed down by hand, and 3 for shock loads.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.