Skip to content
Omnikalc

Reciprocity failure calculator: how long should the shutter stay open?

Enter the exposure time without a filter, the neutral density stops and the film exponent to get the metered time, the corrected exposure time and the extra stops.

Updated on
Your inputs
s

Value out of range

stops

Value out of range

Value out of range

Results

Corrected exposure time

1:34

Metered exposure time
0:32
Extra stops of exposure
1.55 stops
Total stops compared with the unfiltered time
7.55 stops

Film becomes less sensitive during very long exposures, so a night shot or a strong neutral density filter needs extra time. The reciprocity failure calculator takes the exposure time without a filter, the stops of neutral density and the film’s reciprocity exponent and gives the metered exposure time, the corrected exposure time, the extra stops and the total stops.

How the calculation works

  • Metered time = exposure time without a filter × 2^(stops of the neutral density filter). Each stop doubles the time.
  • Corrected time = metered time^p, where p is the reciprocity exponent of the film (the Schwarzschild or Ilford-type formula). The correction applies only above 1 second.
  • Extra stops = log₂(corrected time ÷ metered time). It is the additional exposure that the film needs beyond the metered value.
  • Total stops = log₂(corrected time ÷ time without the filter). It is the full compensation compared with the exposure that you started from.

Example

A scene needs 0.5 s with no filter and a 6-stop neutral density filter is added, so the metered time is 0.5 × 2⁶ = 32 s. With a film exponent of 1.31, the corrected time is 32^1.31 = 93.7 s, or 1:34. That is 1.55 extra stops beyond the meter reading, and 7.55 stops in total compared with the exposure without the filter.

Why it matters

Long exposures are the heart of night, waterfall and architecture photography on film. A strong filter pushes the time into the range where the film fails, and a wrong guess ruins a frame that you cannot repeat. The corrected time takes the guesswork out of it.

Good to know

This is the power law used by several film makers, and it only fits the range given on the data sheet. Some films have no correction up to a given time, and others have a table that is more exact than the formula. Color films also need filter changes, and reciprocity changes with temperature. Always bracket important shots.

The exposure value calculator links aperture, time and sensitivity and the astrophotography exposure calculator plans the time for a night sky frame.

Frequently asked questions

What is reciprocity failure?

Film follows the rule that exposure equals light times time only over a wide middle range of times. At very long or very short exposures, film responds less than the rule predicts, so you must give more exposure than the meter says. For black-and-white film the effect starts at about 1 second.

Where do I find the exponent?

The film maker’s data sheet gives either a formula with an exponent or a table of corrections. Ilford, for example, publishes corrections of the form Tc = Tm^p for its black-and-white films, with p between about 1.26 and 1.48. If the sheet has a table, use the exposure it lists rather than this formula.

Does a digital camera have reciprocity failure?

No, a digital sensor responds in a linear way for any exposure time. Long exposures show more noise and hot pixels, but you do not need to lengthen the time. The correction here is for film, and for photographic paper in some cases.

Why is the correction often given in a table at 10 seconds and more?

The effect grows quickly with time. A 10 second reading might need 15 to 30 seconds, and a 100 second reading might need 5 to 10 minutes. Color films also shift in color at long exposures, because the three layers fail at different rates, so they need filtration as well.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.