Skip to content
Omnikalc

Resin 3D print layer exposure time calculator

Enter the resin penetration depth, the critical exposure, the light intensity and the layer height to get the exposure time per layer and the total print time.

Updated on
Your inputs
µm

Value out of range

mJ/cm²

Value out of range

mW/cm²

Value out of range

µm

Value out of range

Value out of range

mm

Value out of range

s

Value out of range

Results

Exposure time per layer

6.14 s

Time to reach the critical exposure
2.67 s
Exposure dose per layer
18.4 mJ/cm²
Cure depth aimed
100 µm
Number of layers
800
Total print time
2.03 h

The resin 3D print exposure calculator gives the time to reach the critical exposure, the exposure time per layer, the dose, the cure depth aimed, the number of layers and the total print time from the working curve of the resin.

How the calculation works

  • Enter the penetration depth Dp and the critical exposure Ec of the resin.
  • Enter the light intensity at the vat, the layer height and the cure depth as a multiple of it.
  • Enter the height of the model and the lift time to get the print time.

Example

A resin with a penetration depth of 120 µm and a critical exposure of 8 mJ/cm², lit by 3 mW/cm², starts to gel after 2.67 s. To cure 100 µm for a layer of 50 µm takes 6.14 s, a dose of 18.4 mJ/cm². A model of 40 mm has 800 layers and prints in 2.03 h.

Why it matters

The calculator helps users of resin printers, SLA, DLP and LCD machines, who tune the exposure for a new resin, and makers who want to estimate the duration of a print or the effect of a change in layer height.

Good to know

The exposure time grows exponentially with the cure depth, so a small increase of the cure depth lengthens the exposure a lot. The first layers, the bottom layers, need much longer exposure to stick to the plate, often ten times the normal one. The light intensity at the vat depends on the age of the screen or the lamp and the film, so measure it with a radiometer or recalibrate with a test print. Temperature changes the viscosity and the speed of the reaction. Wear gloves, work in a ventilated room and post-cure the print.

The 3D print cost calculator estimates the filament and resin cost of a part, the epoxy resin calculator handles the quantity for casting, the UV disinfection dose calculator uses the same dose idea, light intensity times time, and the laser beam spot calculator sizes a beam on a surface.

Frequently asked questions

What is the working curve of a resin?

The working curve relates the cure depth Cd to the exposure E: Cd = Dp × ln(E / Ec). Dp is the penetration depth of the light in the resin and Ec the critical exposure at which the resin starts to gel. The exposure is the light intensity times the time. Plot the cure depth of test squares against the log of the exposure to find Dp from the slope and Ec from the intercept.

Why cure deeper than the layer height?

The cure depth must be larger than the layer height to bond each layer to the one below. A multiple of 1.5 to 2.5 is usual. A cure depth that is too small gives layers that delaminate, while one that is too large cures resin where it should not, which blurs the details and widens the printed features.

How do I find Dp and Ec for my resin?

Print a test with squares at increasing exposure times, measure their thickness with a caliper, and plot the thickness against the natural log of the exposure. The slope is Dp and the exposure at zero thickness is Ec. The manufacturer often gives these values on the data sheet. Pigments and dyes lower Dp.

How long will the whole print take?

The total time is the number of layers times the exposure time and the time to lift and peel the layer from the film. A 40 mm model at 50 µm has 800 layers. With 6.1 s of exposure and 3 s for the moves, it takes about 2 hours. Thicker layers cut the time, at the cost of detail.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.