Skip to content
Omnikalc

Microphone sensitivity and output voltage calculator

Enter the sensitivity, the sound level, the preamp gain and the clip level to get the microphone voltage, the preamp output and the loudest sound before clipping.

Updated on
Your inputs
dBV/Pa

Value out of range

dB SPL

Value out of range

dB

Value out of range

V

Value out of range

Results

Microphone output voltage

25.18 mV

Sensitivity in millivolts per pascal
12.59 mV/Pa
Sound pressure
2.000 Pa
Preamp output voltage
2.518 V
Sound level at preamp clipping
104.0 dB SPL

The microphone sensitivity calculator gives the sensitivity in mV/Pa, the sound pressure, the microphone output voltage, the preamp output and the sound level at which the preamp clips.

How the calculation works

  • Enter the sensitivity of the microphone in dBV/Pa and the sound pressure level in dB SPL.
  • Enter the gain of the preamp and its clip level in volts.
  • The calculator converts the level to pascals and the sensitivity to volts per pascal, then applies the gain and finds the loudest sound before clipping.

Example

A microphone of -38 dBV/Pa, which is 12.59 mV/Pa, hears a sound of 100 dB SPL, or 2.000 Pa. It produces 25.18 mV, and a preamp of 40 dB raises this to 2.518 V. With a clip level of 4 V, the chain clips at 104.0 dB SPL.

Why it matters

The calculator helps sound engineers, podcasters, musicians and electronics designers who set the gain of a recording chain, compare microphones, or design an input stage for a microphone or a MEMS sensor.

Good to know

Set the gain so that the loudest sound stays well below the clip level, with a headroom of 10 to 20 dB for a live source. A condenser microphone has an output stage with its own limit, given as the maximum SPL on the data sheet, usually 120 to 140 dB. The calculator assumes a matched load, and a long cable or a low input impedance reduces the signal. Digital microphones and MEMS capsules give a sensitivity in dBFS at 94 dB SPL, which you can convert with the full-scale level of the converter. Keep the gain in the analog stage low enough that the noise of the next stage does not dominate.

The decibel addition calculator adds sound levels, the speaker SPL calculator gives the level of a loudspeaker, the sound distance calculator gives the level at a distance and the dBm converter handles power levels in a signal chain.

Frequently asked questions

What does microphone sensitivity mean?

Sensitivity is the voltage a microphone produces for a sound pressure of 1 pascal, which is 94 dB SPL, usually quoted in dBV/Pa or mV/Pa. A sensitivity of −38 dBV/Pa equals 12.6 mV/Pa. A condenser microphone is typically between −30 and −45 dBV/Pa and a dynamic microphone between −50 and −60 dBV/Pa, so a dynamic microphone needs more gain.

How is the output voltage found?

The sound pressure in pascals is p = 20 µPa × 10^(SPL / 20), and the output voltage is the sensitivity in V/Pa times the pressure. A 100 dB SPL sound is 2 pascals, so the microphone above gives 25 mV. The preamp multiplies the voltage by 10^(gain / 20).

Why does the sound level at clipping matter?

The preamp output cannot exceed its supply, so it clips at a maximum level. The loudest sound the chain can handle is the level at which the amplified voltage reaches that limit. If a drum or a shout exceeds it, the signal distorts, and the remedy is to lower the gain or to switch on the pad of the microphone or the preamp.

Does the calculator include noise?

No. It gives the signal side only. The self-noise of the microphone, in dB(A), sets the quietest sound it can pick up, and the noise of the preamp matters at high gain. The difference between the clipping level and the noise floor is the dynamic range of the chain, and a good studio chain has more than 110 dB.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.