Skip to content
Omnikalc

Mutation rate calculator: Luria-Delbrück p0 method

Enter the cells per culture, the number of parallel cultures and the number without mutants to estimate the mutation rate per cell per generation with the p0 method.

Updated on
Your inputs

Value out of range

Value out of range

Value out of range

Results

Share of cultures with no mutants (p₀)

30.0%

In the usual reliable range, 10 to 70 %

Mutation rate per cell per generation

1.2 × 10⁻⁸

Mutations per culture (m = −ln p₀)
1.204
Mutations per billion cell divisions
12.0

A mutation rate says how often a cell acquires a change per generation, and it is among the hardest numbers in biology to measure. This mutation rate calculator uses the Luria-Delbrück p₀ method: from the cells per culture, the number of parallel cultures and the number with no mutants it estimates the mutations per culture and the mutation rate.

How the calculation works

  • p₀ = cultures with no mutants ÷ total parallel cultures. It is the fraction of cultures where no mutation happened.
  • Mutations per culture m = −ln(p₀), from the Poisson distribution of mutation events across the cultures.
  • Mutation rate μ = m ÷ number of cells in a culture at the end of growth, per cell per generation.
  • Per billion divisions = μ × 1,000,000,000, which makes small rates easier to read.

Example

In a Luria-Delbrück experiment, 30 parallel cultures each grow to 100,000,000 cells and 9 of them contain no resistant mutant. Then p₀ = 9 ÷ 30 = 30 %. The mutations per culture are −ln(0.3) = 1.204, and the mutation rate is 1.204 ÷ 100,000,000 = 1.20 × 10⁻⁸ per cell per generation, or 12.0 per billion divisions.

Why it matters

Mutation rates matter for understanding how bacteria become resistant to antibiotics, how cancers evolve, how fast viruses change and how to design a vaccine or a drug. The Luria-Delbrück experiment of 1943 showed that mutations arise at random before selection, and the p₀ method is its simplest quantitative form.

Good to know

The p₀ method works best when the empty fraction is between 0.1 and 0.7, so adjust the culture size or the number of cultures to land in that range. It assumes that mutants grow as fast as normal cells, that the number of cells at the end is large and that there is no back mutation. If mutants grow slower, the rate is underestimated. Fluctuation experiments with more careful estimators, such as the Ma-Sandri-Sarkar maximum likelihood method, give better confidence intervals and should be used for publication.

The cell doubling time calculator links growth and generations, the Hardy-Weinberg calculator covers allele frequencies in populations and the serial dilution calculator helps plate the right number of cells.

Frequently asked questions

What is the p0 method?

It estimates the mutation rate by counting the cultures that have no mutants. Because mutations are rare and random, the number per culture follows a Poisson law, so the empty fraction is p₀ = e^(−m).

Why use parallel cultures?

Mutations arise at random during growth. An early mutation gives many mutant cells and a late one gives few, which makes the counts vary greatly (the Luria-Delbrück jackpot effect). Counting empty cultures is a robust way to handle this.

What is the difference between mutation rate and mutation frequency?

The rate is the chance of a mutation per cell per generation. The frequency is the fraction of mutant cells in a population at one time, which depends on when mutations happened and on their growth.

What is a typical value?

Spontaneous rates for a single gene in bacteria are around 10⁻⁷ to 10⁻¹⁰ per cell per generation. Antibiotic resistance genes usually fall in this range.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.