Skip to content
Omnikalc

Slew rate calculator: can your op amp follow a fast, large signal?

Enter the amplitude, the frequency and the slew rate of an op amp to get the required slew rate, the margin, the full-power bandwidth and the largest undistorted amplitude.

Updated on
Your inputs
V

Value out of range

kHz

Value out of range

V/µs

Value out of range

Results

Required slew rate

1.257 V/µs

Margin (op amp slew rate / required)
7.162 ×
Enough margin: no slew-rate distortion
Full-power bandwidth of the op amp
143.24 kHz
Largest undistorted amplitude at this frequency (slew limit only)
71.620 V

An amplifier cannot change its output voltage infinitely fast. The slew rate calculator gives the slew rate required for a sine wave of a given amplitude and frequency, compares it with the slew rate of the op amp, and gives the margin, the full-power bandwidth and the largest undistorted amplitude.

How the calculation works

  • Enter the peak amplitude of the output signal, its frequency and the slew rate of the op amp from its datasheet.
  • The steepest slope of a sine wave Vp sin(2π f t) is 2π f Vp. This is the required slew rate.
  • If the op amp slew rate is lower than this, the output cannot follow and the wave is distorted.
  • The calculator also gives the margin, the full-power bandwidth FPBW = SR / (2π Vp) and the largest undistorted amplitude at the frequency.

Example

An audio op amp with a slew rate of 9 V/µs must output a 10 V peak sine wave at 20 kHz. The required slew rate is 2π × 20,000 × 10 = 1.257 V/µs. The margin is 7.162, so there is no slew-rate distortion. The full-power bandwidth is 143.2 kHz.

Why it matters

Slew-rate limiting is one of the main causes of distortion in op amp circuits that handle large signals at high frequencies, such as audio power stages, filters, instrumentation and pulse circuits. A quick check with this formula avoids choosing an op amp that cannot follow the signal.

Good to know

The calculator applies to a sinusoidal output and to the slew rate in a single direction, and the slew rate of a real op amp can differ for rising and falling edges, and depends on the load, the supply voltage and the temperature. For a square wave or a pulse, the rise time is what matters, and a step of ΔV takes ΔV/SR to complete. The undistorted amplitude shown is limited by the slew rate only, and the supply voltage or the output swing may be smaller.

The op-amp gain calculator gives the closed-loop gain whose bandwidth also limits the signal, the RC filter calculator covers the filters built around the op amp, the Nyquist sampling calculator covers the rate of the converters that follow it, and the total harmonic distortion calculator measures the distortion that a low slew rate produces.

Frequently asked questions

What is the slew rate?

It is the maximum rate of change of the output voltage of an amplifier, in volts per microsecond. It is set by the current that the internal stage can deliver to charge the compensation capacitor. If the input asks for a faster change, the output slews at this maximum rate and cannot go faster, whatever the gain.

What is the effect of a slew rate that is too low?

A sine wave turns into a triangle wave, a square wave gets sloped edges, and harmonic distortion rises. Unlike the clipping at the supply, the distortion appears only at large amplitudes and high frequencies. A small signal at a high frequency may pass without trouble, while a large one at the same frequency is distorted.

What is the full-power bandwidth?

It is the highest frequency at which the amplifier can give its full output swing without slew-rate distortion: FPBW = SR / (2π Vp). It is often much lower than the small-signal bandwidth given by the gain–bandwidth product. For an op amp with a slew rate of 0.5 V/µs, as the 741, the full-power bandwidth at 10 V is only about 8 kHz.

How do I choose an op amp?

Compute the required slew rate for the largest amplitude and the highest frequency of the signal, then choose an op amp whose slew rate is at least two to five times higher, to leave a margin. For audio at 20 kHz and 10 V peak, about 1.3 V/µs is needed. Video, pulse and high-speed data converters require tens to thousands of V/µs.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.