Skip to content
Omnikalc

Strouhal number calculator: at what frequency do vortices leave a cylinder?

Enter the fluid, the flow speed, the cylinder diameter and the natural frequency to get the Strouhal number, the vortex shedding frequency and a resonance check.

Updated on
Your inputs
mph

Value out of range

in

Value out of range

Hz

Value out of range

Results

Vortex shedding frequency

104.45 Hz

Strouhal number
0.1978
Reynolds number
22,710
Regular vortex shedding
Shedding period
9.57 ms
Shedding frequency ÷ natural frequency
0.70
Away from resonance

A cylinder in a flow sheds vortices at a regular frequency, and this can make a wire sing or a chimney sway. The Strouhal number calculator finds the vortex shedding frequency from the fluid, the flow speed and the diameter, with the Roshko correlation. It gives the Strouhal number, the Reynolds number, the period and the ratio to the natural frequency of the structure.

How the calculation works

  • Choose the fluid (air or water) and enter the flow speed, the diameter of the cylinder and the natural frequency of the structure.
  • The calculator finds the Reynolds number Re = U D / ν, then the Strouhal number from the Roshko fit St = 0.198 (1 − 19.7 / Re).
  • The shedding frequency is f = St × U / D, the frequency at which vortices leave alternate sides of the cylinder.
  • It compares this frequency with the natural frequency to warn of a possible resonance, known as lock-in.

Example

Air blows at 30 mph (13.4 m/s) across a cable or pole of 1 in diameter. The Reynolds number is 22,710 and the Strouhal number is 0.198. The vortices shed at 104.5 Hz, a period of 9.6 ms. With a natural frequency of 150 Hz, the ratio is 0.70, so the structure is away from resonance.

Why it matters

Flow-induced vibration is a design problem for chimneys, antenna masts, power lines, cable-stayed bridges, heat exchanger tubes, thermowells and offshore risers. A quick calculation of the shedding frequency shows when a resonance can happen, and it explains the humming tone of a wire in the wind (the Aeolian tone).

Good to know

The correlation is for a smooth, circular, stationary cylinder in a steady and uniform flow, between Reynolds numbers of about 47 and 200,000, with a fixed viscosity for air and water at 68 °F (20 °C). Other shapes have other Strouhal numbers (a square section about 0.13, a flat plate about 0.15), and roughness, turbulence, end effects and a nearby wall change the value. Use it as a first screening, not as a design check.

The Reynolds number calculator gives the flow regime that sets the shedding, the drag force calculator gives the mean load, the pipe resonance calculator covers standing waves in a pipe, and the Mach number calculator covers the speed of compressible flow.

Frequently asked questions

What is the Strouhal number?

It is the dimensionless number St = f L / U that links the frequency f of an oscillating flow to the speed U and a length L, here the diameter of a cylinder. For a circular cylinder over a wide range of Reynolds numbers (about 300 to 200,000), St is close to 0.2, so the shedding frequency is about one fifth of U / D.

What is a vortex street?

Behind a bluff body such as a cylinder, the flow separates and rolls up into vortices that leave the body alternately from the two sides. They form two rows, the von Kármán vortex street. Each vortex gives an alternating side force, so the body is pushed sideways at the shedding frequency and drag fluctuates at twice that rate.

What is lock-in?

When the shedding frequency comes near a natural frequency of the structure, the vibration of the body can take control of the shedding, which then follows the motion over a range of speeds. The result is large and sustained vibration. It is the cause of the singing of wires, the sway of chimneys, bridge hangers, risers of offshore platforms and the Tacoma Narrows type of problems.

How is vibration avoided?

The designer changes the natural frequency (stiffer or shorter members), adds damping, or breaks the regular shedding with helical strakes, shrouds or a change of the cross-section. A margin of about 20 % between the shedding frequency and the natural frequency is a common first rule, but a structural analysis is needed for real structures.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.