Skip to content
Omnikalc

Stanton number calculator: how efficiently does the flow take up heat?

Enter the heat transfer coefficient, the fluid properties and the velocity to get the Stanton number, the Colburn j-factor and the friction coefficient from the analogy.

Updated on
Your inputs
BTU/h·ft²·°F

Value out of range

lb/ft³

Value out of range

ft/s

Value out of range

BTU/lb·°F

Value out of range

Value out of range

Results

Stanton number

0.00206

Colburn j-factor St × Pr^⅔
0.00164
Friction coefficient Cf from the analogy, Cf = 2 j
0.00328
Heat capacity flux ρ V cp
1,944.0 BTU/h·ft²·°F

The Stanton number is a dimensionless heat transfer coefficient for forced convection. This Stanton number calculator finds it from the heat transfer coefficient, the density, the velocity and the specific heat of the fluid, and with the Prandtl number gives the Colburn j-factor and an estimate of the friction coefficient from the Reynolds–Colburn analogy.

How the calculation works

  • Enter the heat transfer coefficient h, the density, the velocity and the specific heat of the fluid, and its Prandtl number.
  • The Stanton number is St = h / (ρ V cp), the heat transferred to the fluid divided by the heat it could carry at the free-stream conditions.
  • The Colburn j-factor is j = St × Pr^⅔, which makes the heat transfer data of different fluids fall on the same curve.
  • By the Reynolds–Colburn analogy, j is about Cf / 2, so the heat transfer coefficient gives an estimate of the skin friction.

Example

Air with a density of 0.075 lb/ft³ and a specific heat of 0.24 BTU/lb·°F flows at 30 ft/s. A surface with h = 4 BTU/h·ft²·°F has a Stanton number of 0.00206. With Pr = 0.71, the Colburn factor is 0.00164, and the analogy gives a friction coefficient Cf of about 0.00328.

Why it matters

The Stanton number and the j-factor are used to compare heat transfer data of different fluids and geometries, to extrapolate test results to other conditions, and to link heat transfer with friction in heat exchangers, turbine blades and boundary layer calculations.

Good to know

The calculator uses the definition of St with the free-stream or mean velocity, and the analogy between friction and heat transfer is valid for flows with no form drag, such as flat plates and smooth tubes, for Prandtl numbers between about 0.6 and 60. It does not compute h itself, which must come from a correlation or a test. Use consistent units for density, velocity, specific heat and the coefficient.

The Nusselt number calculator covers the other dimensionless coefficient, the Prandtl number calculator covers the fluid property used in the j-factor, the Reynolds number calculator covers the flow regime, and Newton’s law of cooling calculator uses the coefficient.

Frequently asked questions

What is the Stanton number?

It is St = h / (ρ V cp) = Nu / (Re Pr), the ratio of the heat actually transferred to the fluid to the thermal capacity of the fluid flow. It is a dimensionless heat transfer coefficient that is most useful in forced convection, where the velocity is known. For turbulent flow in pipes and over plates, St is of the order of 0.001 to 0.005.

What is the Colburn j-factor?

It is j = St Pr^⅔. Colburn found that heat transfer data for fluids of different Prandtl numbers (0.6 to 100) fall on one curve when plotted this way, in the same way as the friction coefficient. It lets a designer use air data for water or the reverse, with a correction for the Prandtl number.

What is the Reynolds–Colburn analogy?

For a flat plate and a turbulent flow in pipes, the heat transfer and the friction follow the same mechanism, so St Pr^⅔ ≈ Cf / 2. A measure of the friction gives the heat transfer, and the other way around. The analogy fails when there is form drag, as around bluff bodies and in tube banks, where the pressure forces add friction without heat transfer.

How do I find the Prandtl number?

It is Pr = cp μ / k, the ratio of the diffusion of momentum to heat. It is about 0.7 for air and other gases, about 7 for water at 68 °F (20 °C), and 100 to 10,000 for oils. Its value for a fluid at a given temperature is in property tables.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.