Skip to content
Omnikalc

Thevenin equivalent calculator: equivalent circuit, load power and maximum power transfer

Enter a source, a series resistor, a shunt resistor and a load to get the Thevenin voltage and resistance, the load current, voltage and power, and the maximum power transfer.

Updated on
Your inputs
V

Value out of range

Ω

Value out of range

Ω

Value out of range

Ω

Value out of range

Results

Thevenin voltage

8.250 V

Thevenin resistance
68.75 Ω
Load current
37.714 mA
Load voltage
5.657 V
Power in the load
213.36 mW
Maximum power the circuit can deliver
247.50 mW
Load power as a share of the maximum
86.2 %
The load is not matched: the maximum power is delivered when the load equals the Thevenin resistance

Any network of sources and resistors can be reduced to a voltage source and one resistor. The Thevenin equivalent calculator does it for a divider with a load: it gives the Thevenin voltage and resistance, the load current, voltage and power and the maximum power transfer.

How the calculation works

  • The circuit is a source in series with R1, with R2 from the node to ground, and a load resistor connected across R2.
  • Enter the source voltage, R1, R2 and the load resistance in ohms.
  • The calculator replaces the source, R1 and R2 by the Thevenin equivalent: Vth = Vs × R2 / (R1 + R2) in series with Rth = R1 ∥ R2.
  • It then gives the load current and voltage, the power in the load, and the maximum power, Vth² / (4 Rth), reached when the load equals Rth.

Example

A 12 V source feeds a divider with R1 = 100 Ω and R2 = 220 Ω, and a load of 150 Ω is connected across R2. The Thevenin voltage is 12 × 220 / 320 = 8.250 V and the Thevenin resistance is 100 ∥ 220 = 68.75 Ω. The load current is 37.714 mA, the load voltage 5.657 V and the power 213.36 mW. The maximum power is 247.50 mW, so the load receives 86.2 % of it.

Why it matters

The calculator helps students, hobbyists and engineers to simplify a circuit, to see the effect of a load on a divider, to choose a load for the maximum power and to check a sensor or a bias network. It is a basic tool of circuit analysis.

Good to know

The calculator is for a linear circuit with DC sources and resistors, for the circuit of a source, a series resistor, a shunt resistor and a load. Real sources have their own internal resistance, which you should add to R1, and real loads such as diodes or motors are not linear. The power ratings of the resistors must be checked too. For AC circuits, use the impedances.

The voltage divider calculator covers the unloaded divider, the Wheatstone bridge calculator covers a bridge circuit, the resistors calculator finds series and parallel values, and the RLC impedance calculator covers AC circuits.

Frequently asked questions

What is Thevenin’s theorem?

Thevenin’s theorem says that any linear circuit with sources and resistors, seen from two terminals, behaves like a single voltage source Vth in series with a single resistor Rth. Vth is the open-circuit voltage between the terminals, and Rth is the resistance seen from the terminals when the sources are set to zero. The theorem was found by Hermann von Helmholtz in 1853 and by Léon Charles Thévenin in 1883, and it makes it easy to find the effect of different loads.

What is the maximum power transfer theorem?

A load receives the largest power from a source with an internal resistance Rth when its resistance equals Rth. The maximum power is Vth² / (4 Rth). At this point the efficiency is only 50 %, since half of the power is lost in Rth. For a power supply we want a small Rth and a high efficiency, and for a signal or a radio we often want the match to get the most signal power.

How do I find the Thevenin resistance?

Remove the load, replace the voltage sources by short circuits and the current sources by open circuits, and compute the resistance between the two terminals. In this circuit, the source is shorted so that R1 and R2 are in parallel: Rth = R1 R2 / (R1 + R2). Another way is to divide the open-circuit voltage by the short-circuit current of the terminals.

Why is the load voltage lower than the Thevenin voltage?

Because the load draws a current, and this current creates a voltage drop across Rth. The load voltage is Vth × RL / (Rth + RL), a new divider. The heavier the load (the lower RL compared with Rth), the lower the voltage. A load much higher than Rth gets almost the open-circuit voltage, but receives very little power.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.