Skip to content
Omnikalc

Vehicle center of gravity height calculator

Enter the weight of the front axle with the car level and with the rear axle lifted, the wheelbase, the lift height and the tire radius to get the height of the center of gravity and its position.

Updated on
Your inputs
lb

Value out of range

lb

Value out of range

lb

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

Results

Height of the center of gravity

20.0 in

Distance of the center of gravity from the rear axle

59.4 in

Angle of the car when lifted
12.8 °
Weight gained by the front axle
54.0 lb
Height above the wheel center
8.0 in
Front share of the weight
55.0 %
Height as a share of the wheelbase
18.5 %

The vehicle center of gravity height calculator finds the height of the center of gravity and its distance from the rear axle from the weight of the front axle with the car level and with the rear axle lifted, the wheelbase, the lift height and the tire radius.

How the calculation works

  • Weigh the front axle with the vehicle level and with the rear axle lifted, and enter both with the total weight.
  • Enter the wheelbase, the lift height at the rear axle and the tire rolling radius.
  • Read the height of the center of gravity and its position.

Example

A vehicle of 3200 lb has 1760 lb on the front axle when level and 1814 lb with the rear axle lifted by 24 in. The car tilts by 12.8 ° and the front axle gains 54.0 lb. The center of gravity is 20.0 in above the ground, 8.0 in above the wheel center, and 59.4 in ahead of the rear axle. The front carries 55.0 % of the weight, and the height is 18.5 % of the wheelbase.

Why it matters

The calculator helps racers, builders, engineers and students who need the height of the center of gravity of a vehicle to model its handling, compute weight transfer and rollover thresholds, or compare the effect of a modification such as lowering the car or adding a roof load.

Good to know

Weigh on a level surface, with the vehicle in running order and the same fuel and driver for both readings. Chock the front wheels and fix the front axle so that it cannot move forward when the rear is raised, and keep the lift height as large as is safe. The ratio between the gain and the weight is small, so the result is very sensitive to the scale accuracy: repeat the weighing and average. Make sure that the tire pressures do not change between readings. The calculation assumes a rigid vehicle without suspension movement, and it works best on a car with the suspension locked.

The center of mass calculator locates a balance point, the corner weights calculator balances the car, the longitudinal weight transfer calculator uses the height under braking and the lateral load transfer calculator uses it in corners.

Frequently asked questions

How can the height of the center of gravity be measured?

The classic method weighs the front axle with the vehicle level and again with the rear axle lifted by a known height. As the rear is raised, the center of gravity moves forward over the front axle and the front scale reads more. The change in the reading, compared with the geometry of the lifted car, gives the height of the center of gravity.

What is the formula?

With the wheelbase L, the lift height H at the rear axle, the total weight W and the gain on the front axle ΔWf, the height is h = r + ΔWf × L / (W × tan θ), where r is the rolling radius of the tires and tan θ = H / √(L² − H²). The result is the height of the center of gravity above the ground.

How accurate is it?

The measurement is sensitive to the readings. A small error in the front weights gives a big error in the height, because the gain is a small difference between two large numbers. Use a lift height large enough to give a gain of at least 1 to 3 percent of the weight, scales that read to 1 pound, and repeat the measurement. Fuel, the driver and anything inside the car must stay in the same place.

Why is the height useful?

The height of the center of gravity sets the weight transfer in braking, acceleration and cornering, and the rollover threshold. Racers measure it to tune a car, and engineers use it for the models of vehicle dynamics. Typical values are 18 to 24 inches for a sedan, 14 to 18 inches for a sports car and 28 to 36 inches for a truck.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.