Skip to content
Omnikalc

Vehicle roll gradient calculator

Enter the vehicle weight, the roll arm, the front and rear wheel rates, the track and the anti-roll bar stiffness to get the total roll stiffness, the roll gradient in degrees per g and the roll angle in a corner.

Updated on
Your inputs
lb

Value out of range

in

Value out of range

lb/in

Value out of range

lb/in

Value out of range

in

Value out of range

lb·in/deg

Value out of range

g

Value out of range

Results

Total roll stiffness

16,137 lb·in/deg

Roll gradient

2.48 °/g

Body roll angle in the corner

1.99 °

Roll stiffness from the springs
14,137 lb·in/deg
Share from the anti-roll bars
12.4 %
Class (1 stiff under 2 °/g, 2 typical up to 3.5, 3 soft)
2

The vehicle roll gradient calculator gives the total roll stiffness from the wheel rates, the track and the anti-roll bars, the roll gradient in degrees per g and the body roll angle in a corner, with a class from stiff to soft.

How the calculation works

  • Enter the vehicle weight, the roll arm and the front and rear wheel rates.
  • Enter the track width, the anti-roll bar stiffness and the lateral acceleration.
  • Read the roll stiffness, the gradient and the roll angle.

Example

The springs of a vehicle of 3200 lb with wheel rates of 250 lb/in and 200 lb/in on a track of 60 in give 14,137 lb·in/deg of roll stiffness. With anti-roll bars of 2000 lb·in/deg, the total is 16,137 lb·in/deg, of which 12.4 % comes from the bars. With a roll arm of 12 in, the roll gradient is 2.48 °/g, which gives a body roll of 1.99 ° at 0.8 g, class 2.

Why it matters

The calculator helps suspension tuners, racers, engineers and students who want to estimate the body roll of a vehicle, compare the effect of stiffer anti-roll bars or springs, and understand why a tall vehicle with soft springs leans so much in a corner.

Good to know

The wheel rate is the spring rate multiplied by the square of the motion ratio, so use the value at the wheel and not at the spring. The roll arm is the vertical distance from the center of gravity to the roll axis, which is typically a few inches above ground at the front and a bit higher at the rear. The calculation is linear and uses the average track. A bar rate is given in the units of torque per degree of roll of the axle. Compare the result with a measurement from a phone inclinometer on the dash during a test.

The lateral load transfer calculator gives the tire loads, the suspension ride frequency calculator relates spring rate to frequency, the center of mass calculator locates the balance point and the torsion spring calculator sizes a bar.

Frequently asked questions

What is the roll gradient?

It is the angle by which the body rolls for each g of lateral acceleration, usually in degrees per g. A sports car is around 1 to 2 degrees per g, a typical passenger car 2.5 to 4, and a tall SUV or van more. A lower gradient gives a more direct feel and a flatter cornering, but a harsher ride on a bump.

What determines the body roll?

The roll moment, which is the weight multiplied by the roll arm and the lateral acceleration, is resisted by the roll stiffness of the suspension. The roll arm is the distance from the center of gravity to the roll axis, an imaginary line through the roll centers. The stiffness comes from the springs, whose contribution grows with the square of the track, and from the anti-roll bars.

How do anti-roll bars help?

An anti-roll bar is a torsion spring that links the two wheels of an axle. It does not act when both wheels move together, so it does not harm the ride, but it resists the difference in height between the wheels in a corner. It adds roll stiffness to reduce body roll without stiffening the springs, and tunes the balance between front and rear.

Is a model with these inputs enough?

It gives a good estimate for the body roll, assuming a linear suspension and a rigid body. It does not include the stiffness of the tires, the bushings or the chassis, which are less important, nor the shift of the roll axis with the movement of the suspension. For a detailed set-up, use measurements of the roll angle on the track.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.