Skip to content
Omnikalc

Suspension ride frequency calculator

Enter the sprung weight at a corner, the spring rate, the motion ratio and the target damping ratio to get the wheel rate, the ride frequency, the static deflection and the damper rate.

Updated on
Your inputs
lb

Value out of range

lb/in

Value out of range

Value out of range

Value out of range

Results

Wheel rate

288.0 lb/in

Ride frequency

1.77 Hz

Damper rate at the wheel for the target ratio

33.7 lb·s/in

Ride frequency in cycles per minute
106 cpm
Static deflection
3.13 in
Critical damping at the wheel
51.8 lb·s/in
Ride class (1 soft under 1.3 Hz, 2 sporty under 2.2 Hz, 3 race)
2

The suspension ride frequency calculator gives the wheel rate from the spring rate and the motion ratio, the ride frequency in Hz and cycles per minute, the static deflection, the critical damping and the damper rate for a target damping ratio, for one corner of a vehicle.

How the calculation works

  • Enter the sprung weight at one corner and the spring rate.
  • Enter the motion ratio and the target damping ratio.
  • Read the wheel rate, the frequency, the deflection and the damper rate.

Example

A corner with 900 lb of sprung weight, a spring of 450 lb/in and a motion ratio of 0.8 has a wheel rate of 288.0 lb/in. The ride frequency is 1.77 Hz, or 106 cpm, ride class 2, with a static deflection of 3.13 in. The critical damping at the wheel is 51.8 lb·s/in, and a ratio of 0.65 needs 33.7 lb·s/in.

Why it matters

The calculator helps people who choose springs and dampers for a car, a kart, a trailer or a motorcycle, and want to compare the ride frequency of their setup with typical values for comfort or racing, or to convert a spring rate into a wheel rate.

Good to know

Use the sprung weight at the corner, which is the weight of the body that the suspension carries, and not the full weight of the vehicle: the unsprung parts such as wheels and brakes are excluded. Measure the motion ratio by comparing the travel of the spring to the travel of the wheel. Use consistent units: pounds per inch with pounds, newtons per millimeter with kilograms. The frequency assumes a linear spring and ignores the stiffness of the tire and the anti-roll bar. The damper rate at the damper is the wheel value divided by the square of the motion ratio.

The compression spring calculator designs a coil, the extension spring calculator handles tension springs, the damping ratio calculator describes an oscillator and the longitudinal weight transfer calculator gives the axle loads.

Frequently asked questions

What is the ride frequency?

It is the natural frequency at which the body of the vehicle bounces on its springs. It depends on the stiffness of the suspension at the wheel and on the mass supported: f = (1 / 2π) × √(wheel rate / mass). Soft passenger cars are around 1.0 to 1.3 Hz, sporty cars 1.5 to 2 Hz, and racing cars 2.5 Hz or more, with aerodynamic downforce.

What is the wheel rate and the motion ratio?

The spring does not always sit directly above the wheel. The motion ratio is the travel of the spring divided by the travel of the wheel. The effective stiffness at the wheel, the wheel rate, is the spring rate multiplied by the square of the motion ratio. A motion ratio of 0.8 reduces the wheel rate to 64 percent of the spring rate.

How should the front and rear frequencies compare?

A common recommendation is to make the rear frequency 10 to 20 percent higher than the front, so that the body pitches less after a bump. The pair of values also affects the balance of the car in handling. The calculator gives the value for one corner, which you can repeat for the other axle.

How is the damper chosen?

The critical damping is the damping at which the body returns to rest without oscillation. A passenger car uses 0.2 to 0.4 of critical on average, with higher values in rebound, and a performance car 0.5 to 0.7. The calculator gives the damping rate at the wheel for the ratio you set, and the damper rate is that value divided by the square of the motion ratio.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.