Skip to content
Omnikalc

Waveguide cutoff calculator: cutoff frequency, usable band and guide wavelength of a rectangular waveguide

Enter the width and the height of a rectangular waveguide, the frequency and the filling to get the TE10 cutoff frequency, the single-mode band, the guide wavelength and the group velocity.

Updated on
Your inputs
mm

Value out of range

mm

Value out of range

GHz

Value out of range

Value out of range

Results

Cutoff frequency of the TE10 mode

6.557 GHz

Upper limit of the single-mode band
13.114 GHz
Position in the single-mode band
52.5 %
Good operating point inside the single-mode band
Wavelength in free space
29.98 mm
Wavelength in the guide
39.71 mm
Group velocity as a share of the speed of light in the filling
0.755

A rectangular waveguide carries microwaves only above a cutoff frequency. The waveguide cutoff calculator gives the TE10 cutoff frequency, the upper limit of the single-mode band, your position in the band, the wavelength in the guide and the group velocity from the inside dimensions.

How the calculation works

  • Enter the inside width a and the inside height b of the rectangular waveguide, in millimeters. A WR-90 guide measures 22.86 × 10.16 mm.
  • Enter the operating frequency in gigahertz and the relative permittivity of the filling. Use 1 for an air-filled guide.
  • The calculator computes the cutoff frequency of the main TE10 mode, f = c / (2a√εr), and the cutoff of the next modes, TE20 and TE01.
  • It gives the upper limit of the single-mode band, your position in the band, the wavelength in the guide λg = λ / √(1 − (fc / f)²) and the group velocity.

Example

A WR-90 waveguide has a width of 22.86 mm and a height of 10.16 mm, filled with air. The cutoff frequency of the TE10 mode is 299.79 / (2 × 22.86) = 6.557 GHz. The next modes start at 13.114 GHz (TE20) and 14.754 GHz (TE01), so the single-mode band ends at 13.114 GHz. At 10 GHz, you are at 52.5 % of the band. The free-space wavelength is 29.98 mm, the guide wavelength is 39.71 mm and the group velocity is 0.755 times the speed of light.

Why it matters

The calculator helps radio amateurs, radar and satellite engineers, microwave students and technicians to choose the right waveguide for a frequency, to check that only one mode propagates and to compute lengths of sections that depend on the guide wavelength, such as filters and stubs.

Good to know

The formulas are for a rectangular guide with perfectly conducting walls, filled with a uniform dielectric. Real guides have losses and tolerances. Standard guides are used between 1.25 and 1.9 times the cutoff of TE10, which is the recommended operating range, where the loss is low and the dispersion is moderate. Stay clear of the cutoff and of the next mode.

The wavelength calculator converts frequency to wavelength in free space, the characteristic impedance calculator covers transmission lines, the coax electrical length calculator relates length and phase in a cable, and the impedance matching calculator designs matching sections.

Frequently asked questions

What is the cutoff frequency of a waveguide?

A hollow metal waveguide carries a microwave only above a minimum frequency, the cutoff frequency. Below it the wave dies out quickly and carries no power. For the lowest mode of a rectangular guide, TE10, the cutoff is c / (2a), where a is the wide side: the guide must be at least half a wavelength wide.

What is the single-mode band?

Between the cutoff of TE10 and the cutoff of the next mode, only one mode can propagate. This is the useful band of the guide. For a guide with a width twice its height, the band goes from fc to 2 × fc. Operating in this band gives a predictable propagation, with no mixing of modes.

Why is the guide wavelength longer than the free-space wavelength?

The wave in a guide bounces between the walls, so its pattern along the axis is stretched. The guide wavelength is λ / √(1 − (fc / f)²), which is always longer than λ and grows without limit near the cutoff. The phase velocity is faster than the speed of light, while the group velocity, which carries energy, is slower.

How does a dielectric filling change the cutoff?

A filling with a relative permittivity εr lowers the cutoff by a factor √εr, so the guide can be smaller for the same frequency. The wavelength inside is also shorter by the same factor. The losses of the dielectric must be taken into account at high frequencies.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.