Skip to content
Omnikalc

Worm gear drive calculator: gear ratio, output speed, lead angle, efficiency and self-locking check

Enter the starts, the wheel teeth, the speed, the pitch, the worm diameter and the friction coefficient to get the ratio, the output speed, the lead angle, the efficiency and the self-locking margin.

Updated on
Your inputs

Value out of range

Value out of range

rpm

Value out of range

in

Value out of range

in

Value out of range

Value out of range

Results

Gear ratio

20.0

Output speed of the wheel
87.5 rpm
Lead angle of the worm
6.06 °
Efficiency of the drive (worm driving)
67.6 %
Torque multiplication (ratio × efficiency)
13.52
Self-locking margin (friction angle − lead angle)
-3.19 °
Not self-locking: the wheel can back-drive the worm

A worm gear gives a large speed reduction in a single stage and can be self-locking. The worm gear drive calculator gives the ratio, the output speed, the lead angle, the efficiency, the torque multiplication and the self-locking margin from the geometry of the worm and the friction.

How the calculation works

  • Enter the number of starts of the worm (1, 2 or 4), the number of teeth of the wheel and the input speed.
  • Enter the axial pitch and the pitch diameter of the worm. The lead is the number of starts times the axial pitch.
  • Enter the coefficient of friction of the mesh, between 0.03 for a well lubricated bronze wheel and 0.15 for poor conditions.
  • The calculator gives the ratio z₂ / z₁, the output speed, the lead angle γ, the efficiency tan γ / tan(γ + ρ) and the self-locking margin ρ − γ, where ρ = arctan μ.

Example

A worm with 2 starts, an axial pitch of 0.25 in and a pitch diameter of 1.5 in drives a 40-tooth wheel at 1,750 rpm. The ratio is 20 and the output speed is 87.5 rpm. The lead is 0.5 in, so the lead angle is 6.06°. With a friction coefficient of 0.05, the friction angle is 2.86° and the efficiency is 67.6 %. The torque is multiplied by 13.52. The margin is −3.19°, so the drive is not self-locking.

Why it matters

The calculator helps engineering students, designers of machines, hoists, gate openers and 3D printers, and makers to choose the number of starts and the diameter of a worm, to see the efficiency, and to check if the drive will hold a load without a brake. It gives a first design before the standard tables.

Good to know

The calculator uses the basic geometry and the efficiency formula for the worm driving the wheel, with a constant friction coefficient and no bearing or seal losses. The pressure angle, the normal friction and the thermal rating are not included. The real friction depends on the materials, the lubricant and the speed, so use catalog values for the final design.

The gear ratio calculator handles spur gear trains, the torque calculator relates force and distance, the horsepower and torque calculator links power and speed, and the pulley calculator handles belt drives.

Frequently asked questions

How is the ratio of a worm gear computed?

The ratio is the number of teeth of the wheel divided by the number of starts of the worm. A single-start worm with a 40-tooth wheel gives a ratio of 40, and a double-start worm with the same wheel gives 20. A single stage can give large ratios in a small space, which is the main advantage of the worm drive.

What is the lead angle?

The lead angle γ is the angle of the thread of the worm on its pitch cylinder. Its tangent is the lead divided by π times the pitch diameter, with the lead equal to the number of starts times the axial pitch. A small lead angle gives high ratios but low efficiency, and a large angle gives better efficiency.

When is a worm gear self-locking?

The drive is self-locking when the lead angle is smaller than the friction angle ρ = arctan μ. Then the wheel cannot drive the worm, which is used in hoists and in adjusters that must hold a load. The friction varies with the speed and the vibration, so a self-locking drive should not be the only safety device for a lifted load.

Why is the efficiency of worm gears low?

The teeth slide on each other with a lot of friction, unlike the rolling contact of spur gears. The efficiency of the worm driving is tan γ / tan(γ + ρ), which is low for a small lead angle. This loss turns into heat, so worm drives need good lubrication and cooling, and they are limited in continuous power.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.