Skip to content
Omnikalc

Critical power calculator: find your CP and W prime and the time you can hold a power

Enter the power and duration of two maximal efforts to get your critical power and W prime, and the time to exhaustion at a target power.

Updated on
Your inputs
W

Value out of range

min

Value out of range

W

Value out of range

min

Value out of range

W

Value out of range

Results

Critical power (CP)

260.0 W

A valid critical power
W′: work capacity above CP
21.6 kJ
Target power as a share of CP
123.1 %
Above CP: W′ is used up at a steady rate
Time to exhaustion at the target power
6:00

How long can you hold a given power? The critical power model answers with two numbers: the critical power (CP), the power you can hold for a long time, and W′, the work you can do above it. The critical power calculator finds both from two maximal efforts and gives the time to exhaustion at a target power.

How the calculation works

  • Do two maximal efforts on separate days: a short one (about 3 minutes) and a long one (about 12 minutes). Enter their average power and duration.
  • The work done in each effort is W = P × t. The calculator fits the line of work against time: W = CP × t + W′.
  • The slope is the critical power (CP), the highest power that can be held for a long time, and the intercept is W′, the finite amount of work that can be done above CP.
  • Enter a target power to see its share of CP and the time to exhaustion, t = W′ / (P − CP).

Example

A cyclist rides 380 W for 3 minutes and 290 W for 12 minutes. The work is 68.4 kJ and 208.8 kJ, so CP = (208.8 − 68.4) / (720 − 180) = 260 W and W′ = 68.4 − 260 × 0.18 = 21.6 kJ. A target of 320 W is 123.1 % of CP and can be held for 21,600 / (320 − 260) = 360 seconds, which is 6 minutes.

Why it matters

The calculator helps cyclists, runners, rowers and coaches to set training zones, to plan pacing in a time trial and to design interval workouts. The model also allows tracking changes of fitness with a short test.

Good to know

The two-parameter model is valid for maximal efforts of about 2 to 30 minutes. It assumes steady power, and real efforts vary with fatigue, heat, nutrition and motivation. The estimates from only two efforts are sensitive to errors: a 2 % error in an effort changes CP by several watts and W′ by a few kilojoules. The test must be done all-out. This is not medical advice.

The FTP zones calculator sets the training zones from the threshold, the cycling power calculator estimates the power for a given speed and slope, the training stress score calculator measures the load of a ride, and the VO2 max calculator estimates the aerobic capacity.

Frequently asked questions

What is critical power?

Critical power is the highest power an athlete can hold in a steady state, without the slow rise of fatigue that comes above it. It marks the border between the heavy and the severe intensity domains. In the two-parameter model, any work done above CP draws on a limited store W′ (pronounced W prime), and the effort ends when W′ is used up. CP is often close to, but a little above, the lactate threshold power and often 5 % under the 40-minute power.

How do I run the test?

Do two maximal efforts of different lengths, between about 3 and 20 minutes, on separate days, well rested, with the same equipment and a steady pacing. The efforts must be all-out. A short effort of 3 minutes and a long one of 12 minutes are a common pair, and more efforts (3-parameter or more points) give a better fit. The test needs a power meter or a trainer.

What is W′ and what is it for?

W′ is the work in kilojoules that you can do above CP, a kind of battery for hard efforts such as attacks and sprints. A typical value is 15 to 25 kJ for cyclists. W′ drops when you ride above CP and recovers when you ride below it. Knowing W′ lets you plan how many hard efforts you can do in a race or an interval workout.

What is the difference with FTP?

The FTP is the best average power for about one hour, often taken as 95 % of the 20-minute power. CP is computed from the model and from efforts of different lengths, and is generally a little higher than the FTP. Both are used to set the training zones. The model is not valid for efforts shorter than about 2 minutes or longer than 30 to 40 minutes, so do not use it outside this range.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.