Skip to content
Omnikalc

Critical depth calculator: critical depth and flow regime of an open channel

Enter the flow rate and the width of a rectangular channel, and the actual depth, to get the critical depth, the critical velocity, the minimum specific energy and the Froude number that tells if the flow is subcritical or supercritical.

Updated on
Your inputs
cfs

Value out of range

ft

Value out of range

ft

Value out of range

Results

Critical depth yc

1.459 ft

Flow per unit width q
10.00 ft²/s
Critical velocity Vc
6.85 ft/s
Minimum specific energy Ec = 1.5 yc
2.189 ft
Froude number at the actual depth
0.220
Subcritical flow: slow and deep, controlled from downstream
Specific energy at the actual depth
4.097 ft

The critical depth separates the slow, deep flows from the fast, shallow ones in an open channel. The critical depth calculator gives the critical depth, the critical velocity, the minimum specific energy and the Froude number of a rectangular channel from the flow rate and the width.

How the calculation works

  • Enter the flow rate in the channel, the width of the rectangular section, and the actual depth of the water if you want to know the flow regime.
  • The calculator finds the flow per unit width q = Q / b, and the critical depth yc = (q² / g)^(1/3), at which the specific energy of the flow is the lowest.
  • It gives the critical velocity Vc = √(g yc), the minimum specific energy Ec = 1.5 yc and the Froude number at the depth that you entered.
  • A Froude number below 1 is a subcritical flow, deep and slow. Above 1, it is supercritical, shallow and fast.

Example

A rectangular channel of 10 ft carries 100 cfs. The flow per unit width is 10 ft²/s. The critical depth is (10² / 32.174)^(1/3) = 1.459 ft, the critical velocity is 6.85 ft/s and the minimum specific energy is 2.189 ft. At the actual depth of 4 ft, the velocity is 2.5 ft/s and the Froude number is 0.220: the flow is subcritical, with a specific energy of 4.097 ft.

Why it matters

The calculator helps civil and environmental engineers, hydrology students and drainage designers to know if a flow is subcritical or supercritical, to find the control section of a channel, and to check the depth at a weir, a drop or a constriction. It is the first step of a water surface profile.

Good to know

Check the regime before choosing the method of analysis: the profile is computed upstream for subcritical flow and downstream for supercritical flow. Avoid designing a channel with a Froude number between 0.8 and 1.2, where the flow is unstable. Remember that the critical depth does not depend on the roughness of the channel.

The hydraulic jump calculator gives the depths across a jump, the Froude number calculator covers the dimensionless number, the Manning equation calculator gives the normal depth and the broad-crested weir calculator uses the critical depth over the crest.

Frequently asked questions

What is the critical depth?

The specific energy of an open channel flow is E = y + V² / 2g, the depth plus the velocity head. For a given flow rate, there are two depths with the same energy, a deep and slow one, and a shallow and fast one. The critical depth is the depth where the energy is the lowest. At this depth, the Froude number is 1, and the velocity is equal to the speed of a small wave on the water surface.

How is it computed for a rectangular channel?

For a rectangular section, the condition of minimum energy gives yc = (q² / g)^(1/3), where q is the flow per unit width. The minimum specific energy is Ec = 1.5 yc, and the critical velocity is Vc = √(g yc). The critical depth depends only on the flow and the width, not on the slope or the roughness of the channel.

What does the Froude number tell?

The Froude number is Fr = V / √(g y). If Fr is less than 1, the flow is subcritical (or tranquil): a wave can travel upstream, and the flow is controlled from downstream. If it is more than 1, the flow is supercritical (or rapid): the waves are swept downstream, and the control is upstream. A transition from supercritical to subcritical flow makes a hydraulic jump.

What are the limits of this calculator?

It is valid for a prismatic rectangular channel with a hydrostatic pressure, a uniform velocity and a small slope. Trapezoidal and circular sections need an iteration, since their critical depth depends on the shape. The calculator does not include the friction losses, the air entrainment, the curvature of the flow or the unsteady effects. Near the critical depth, small changes in the energy make large changes in depth.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.