Skip to content
Omnikalc

Abrasive blasting media consumption and production calculator

Enter the surface to blast, the cleanliness standard and the price of the abrasive to get the blasting time, the mass of abrasive and its cost.

Updated on
Your inputs
ft²

Value out of range

$ per ton

Value out of range

Results

Blasting time

13.3 h

Abrasive used
8,000 lb
Abrasive used in tons
4.0 tons
Cost of the abrasive
720 $

The abrasive blasting calculator gives the blasting time, the mass of abrasive and its cost for a steel surface, from the surface to blast, the cleanliness standard and the price of the abrasive per ton.

How the calculation works

  • Enter the surface to blast and choose the cleanliness standard of the specification.
  • Enter the price of the abrasive per ton.
  • The calculator finds the blasting time, the mass of abrasive, the tons of abrasive and its cost.

Example

A steel surface of 2,000 ft² is blasted to the commercial blast standard (SP 6), with a production of 150 ft² per hour, so the work takes 2,000 / 150 = 13.3 hours. At 4 lb of abrasive per square foot, the job uses 8,000 lb, that is 4.0 tons, and at $180 per ton the abrasive costs $720.

Why it matters

The calculator helps painting contractors, fabricators, bridge and tank owners, estimators and facility managers to estimate the time and the abrasive for a blasting job, to compare the cleanliness standards, and to order the right quantity of abrasive for the days of the job.

Good to know

Blast to the standard that the coating manufacturer asks for and not to a cleaner one, because a white metal blast costs about twice as much as a commercial blast. Measure the real production on a test area of the job, and keep a reserve of 10 percent of abrasive for the losses. Blast only when the steel is at least 5 °F above the dew point, and coat the same day, before flash rust appears. Check the humidity of the air too, because blasting in a wet or foggy morning brings back the rust within hours, and plan the abrasive deliveries so that the pot is never left empty during a shift.

The spray-applied fireproofing calculator gives the thickness and the quantity of fireproofing, the paint calculator gives the quantity of paint for a surface, the painting cost calculator gives the cost of a painting job and the lead paint removal cost calculator gives the cost of removing old coatings.

Frequently asked questions

What are the cleanliness standards?

The standards of the Society for Protective Coatings and NACE describe how clean the steel must be before it is coated. SP 6 is the commercial blast, where two thirds of each square inch must be free of rust and old coating. SP 10 is the near-white blast, with 95 percent clean, and SP 5 is the white metal blast, where the steel is clean everywhere. The cleaner the standard, the slower the work and the more abrasive it uses.

Where do the production rates come from?

The calculator uses typical rates for blasting with a pressure pot and a 3/8 in nozzle at about 100 psi, which are 150, 100 and 70 square feet per hour for the three standards, and an abrasive consumption of 4, 6 and 8 lb per square foot. The real values depend on the abrasive, the nozzle, the pressure, the profile required, the shape of the steel and the skill of the operator, so use your own measured rates when you have them.

Can the abrasive be reused?

Steel grit and steel shot can be recycled several times with a recovery system, and then the consumption per square foot is much lower than the values given here. Expendable abrasives such as coal slag, garnet or silica substitutes are used once. For an expendable abrasive, the consumption in this calculator is a good first estimate, and the disposal of the spent abrasive must be added to the cost.

What does the calculator leave out?

The calculator gives the abrasive and the blasting time only. It does not include the setup, the containment, the dust collection, the compressor, the labor rate, the cleanup, the testing of the profile, the disposal of lead-containing debris or the time lost when the work is stopped by the weather. Add these items to the budget of the job.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.