Skip to content
Omnikalc

Weld metal volume and electrode consumption calculator

Enter the leg size, the weld length, the process, the deposition rate and the operating factor to get the weld metal, the filler to buy and the welding time.

Updated on
Your inputs
in

Value out of range

ft

Value out of range

Value out of range

lb/h

Value out of range

%

Value out of range

Results

Filler metal to buy

50.9 lb

Volume of weld metal
165.0 in³
Weight of weld metal deposited
46.9 lb
Arc time
5.9 h
Total welding time at the operating factor
19.5 h

The weld metal calculator gives the volume and the weight of the weld metal of fillet welds, the filler wire or electrodes to buy with the deposition efficiency of the process, the arc time and the welding time, from the leg size and the length.

How the calculation works

  • Enter the leg size and the total length of the fillet welds, and the profile factor.
  • Choose the welding process for the deposition efficiency, then enter the deposition rate and the operating factor.
  • The calculator gives the volume and the weight of weld metal, the filler to buy, the arc time and the welding time.

Example

400 ft of fillet weld with a 1/4 in leg and a profile factor of 1.1 has a section of 0.5 × 0.25² × 1.1 = 0.0344 in² and a volume of 0.0344 × 4,800 = 165.0 in³. At 0.284 lb/in³ this is 46.9 lb of weld metal. With solid wire (92 %) you buy 46.9 / 0.92 = 50.9 lb. At 8 lb/h the arc time is 5.9 h, and at an operating factor of 30 % the welding takes 19.5 h.

Why it matters

The calculator helps fabricators, estimators, welding supervisors and site managers to order the filler metal, to compare processes, and to estimate the hours of welding of a job before the quote or before the shop drawings are complete.

Good to know

Keep the leg size no larger than the design needs, since the weld metal grows with the square of the leg: a 1/4 in weld has 78 % more metal than a 3/16 in weld and a 3/8 in weld has more than twice as much as a 1/4 in weld. A smaller weld in more passes is not always cheaper, so check the process, the position and the cost of the labor. Count the filler by lot, and store low hydrogen electrodes dry according to the supplier.

The fillet weld strength calculator gives the capacity of a weld, the welding heat input calculator gives the energy per length, the weld preheat calculator gives the preheat temperature and the carbon equivalent calculator gives the weldability of the steel.

Frequently asked questions

How is the weld metal volume found?

A fillet weld with equal legs has a triangular section of area w²/2, where w is the leg size. The volume is that area times the length, increased by a profile factor of 1.05 to 1.2 for the convex face, the root penetration and the reinforcement. A concave weld, or one ground flush, needs a factor close to 1.0. For a groove weld use the area of the groove, which depends on the angle and the gap.

What is the deposition efficiency?

The deposition efficiency is the share of the filler that ends in the weld. Stick electrodes lose the stub of about 50 mm (2 in) and the flux and spatter, and the efficiency is near 60 %. Solid wire loses only a little spatter and reaches 92 to 95 %, flux-cored wire is near 85 %, and submerged arc is near 98 %. The calculator divides the weld metal by this efficiency to get the filler to buy.

What are the deposition rate and the operating factor?

The deposition rate is the weight of metal laid per hour of real arc time, and it depends on the process, the wire size and the current. The operating factor is the share of the working time with the arc on, from about 20 to 30 % for manual stick or semi-automatic work on a site, to 60 % or more for a mechanized shop. Dividing the arc time by this factor gives the welding time of the job.

What does the calculator leave out?

The calculator does not count the shielding gas, the flux, the preparation and cleaning, the tacking, the fit-up, the position of the weld or the repair. It assumes a steel density of 0.284 lb/in³, that is 7.85 g/cm³. Treat the result as a base figure for ordering the filler, and add 5 to 10 % for the small lots and the waste of the site.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.