Skip to content
Omnikalc

Ball mill critical speed calculator: how fast a grinding mill should turn

Enter the inside diameter of the mill, the ball size and the operating speed to get the critical speed, the operating speed in rpm, the practical speed range of 65 to 82% of critical and the peripheral speed.

Updated on
Your inputs
ft

Value out of range

in

Value out of range

%

Value out of range

Results

Critical speed

27.53 rpm

Operating speed
20.64 rpm
Operating speed as a share of critical
75.0 %
Normal grinding speed: the balls cataract
Lower practical speed (65% of critical)
17.89 rpm
Upper practical speed (82% of critical)
22.57 rpm
Peripheral speed of the shell
518.9 ft/min

The ball mill critical speed calculator gives the critical speed of a grinding mill from its inside diameter and ball size, the operating speed at a chosen share of critical, the practical range of speeds and the peripheral speed of the shell.

How the calculation works

  • Enter the inside diameter of the mill (measured inside the liners) and the diameter of the largest grinding balls.
  • Enter the operating speed as a share of the critical speed (65 to 82% for most ball mills, 75% is usual).
  • The calculator finds the critical speed Nc = 76.63 / √(D − d), with D and d in feet, which is the speed at which the balls stick to the shell by centrifugal force.
  • It gives the operating speed, the practical speed range from 65% to 82% of critical and the peripheral speed of the shell.

Example

A ball mill has an inside diameter of 8 ft with balls of 3 in (0.25 ft). The critical speed is 76.63 / √(8 − 0.25) = 27.53 rpm. At 75% of critical, the operating speed is 20.64 rpm. The practical range is 17.89 rpm (65%) to 22.57 rpm (82%). The peripheral speed of the shell at the operating speed is π × 8 × 20.64 = 518.9 ft/min.

Why it matters

The calculator helps mineral processing and cement engineers, mill operators, laboratories and students to set the speed of a ball, rod or SAG mill, to check a gearbox or a variable speed drive and to understand why a mill may grind badly. It is a basic check that is used in every grinding circuit.

Good to know

Measure the diameter inside the liners, as it falls when they wear out. Use 70 to 78% of critical for most ball mills, a lower value for rod mills, and a higher value for fine grinding with small balls. Never run a mill at or above the critical speed. Check the drive power and the liner design when you change the speed.

The shaft critical speed calculator covers the whirling of shafts, the horsepower and torque calculator converts the drive power, the gear ratio calculator sizes the reducer and the density calculator converts masses and volumes of the charge.

Frequently asked questions

What is the critical speed of a mill?

The critical speed is the speed at which the centrifugal force on a ball at the shell equals its weight at the top of the rotation. At or above this speed, the balls stay against the shell and do not fall, so no grinding happens. It is Nc = 42.3 / √(D − d) rpm for D in meters, which is 76.63 / √(D − d) for D in feet. A larger mill has a lower critical speed in rpm.

Why do mills run at 65 to 82% of the critical speed?

At about 65% of critical the balls cascade down the slope of the charge, which mostly gives abrasion and fine grinding. Between 70 and 80% they are lifted higher and fall in a cataracting motion that gives impact, which breaks coarse particles. Above 82% the balls hit the liners, which wears them quickly and breaks balls. Most mills turn at 70 to 78%.

Does the ball size matter?

Only slightly. The formula uses the distance between the center of a ball and the mill axis, so it is the mill diameter minus the ball diameter that counts. For a large mill with small balls the correction is a fraction of a percent, but for a small laboratory mill with large balls it is more important. Always measure the diameter inside the liners and not outside the shell.

What about the peripheral speed?

The peripheral speed of the shell is the diameter times pi times the rpm. For a given share of the critical speed it grows with the square root of the diameter. Large mills therefore have a high shell speed, which can limit the choice of the liner and lifter design. It is also a reference for the wear and for the noise of the mill.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.