Skip to content
Omnikalc

Shaft critical speed calculator: first critical speed, frequency and safe operating range

Enter the diameters, the length, the material, the supports and the operating speed to get the first critical speed, its frequency and the ratio to the operating speed.

Updated on
Your inputs
in

Value out of range

in

Value out of range

in

Value out of range

psi

Value out of range

lb/in³

Value out of range

rpm

Value out of range

Results

First critical speed

4,132 rpm

First critical frequency
68.87 Hz
Maximum recommended operating speed (70 % of critical)
2,893 rpm
Operating speed as a share of the critical speed
0.42
Subcritical with a safe margin

The critical speed of a rotating shaft is the speed at which it resonates in bending and begins to whirl. The shaft critical speed calculator gives the first critical speed, its frequency, the maximum recommended operating speed and the ratio of the operating speed to the critical speed for a solid or hollow shaft.

How the calculation works

  • Enter the outer diameter and the inner diameter of the shaft (0 for a solid shaft), and the length between the bearings.
  • Enter the modulus of elasticity and the weight density of the material (30 million psi and 0.284 lb/in³ for steel).
  • Choose the support conditions, which set the factor in the formula: cantilever 1.875, simply supported π, fixed–pinned 3.927 and fixed–fixed 4.730.
  • The calculator gives the first critical speed ω = (βL / L)² √(E I / (ρ A)), where I / A = (D² + d²) / 16 for a tube, the frequency, a recommended maximum speed and the ratio of your operating speed to the critical speed.

Example

A solid steel shaft of 2 in diameter and 48 in between the bearings is simply supported, with E = 30,000,000 psi and a weight density of 0.284 lb/in³. The first critical speed is 4,132 rpm, or 68.87 Hz. The recommended maximum operating speed is 70 % of it, 2,893 rpm. At 1,750 rpm, the ratio is 0.42, so the shaft runs well below the critical speed.

Why it matters

The calculator helps mechanical engineering students, designers of machines, fans, pumps, lathes and drive shafts, and makers to check that a shaft does not run near its resonance. It shows how the diameter, the length and the supports change the critical speed, which grows with the diameter and falls with the square of the length.

Good to know

The formula is for a uniform shaft of constant section with supports at both ends and no added masses. Gears, pulleys, rotors, the stiffness of the bearings and the gyroscopic effect change the result, and the second and higher critical speeds are not given. Treat the value as a first estimate, and use a full rotordynamic analysis or a measurement for important machines such as turbines, compressors and high-speed spindles.

The shaft torsion calculator gives the twist under a torque, the moment of inertia calculator gives the stiffness of a section, the flywheel energy calculator relates mass and speed, and the gear ratio calculator gives the speeds in a gear train.

Frequently asked questions

What is the critical speed of a shaft?

The critical speed, or whirling speed, is the rotation speed at which the shaft turns at the same frequency as its natural frequency of bending. At this speed the small imbalance of the shaft excites a resonance, the deflection grows and the shaft whirls in a large bow. It can destroy bearings and seals, so rotating machines are designed to run away from it.

How far from the critical speed should the machine run?

A common rule keeps the operating speed under about 70 % of the first critical speed, or above about 130 % of it for a supercritical machine. Between these limits the vibration is likely to be strong. Turbines and some centrifuges run above the first critical speed, and they pass through it quickly during start-up and shutdown.

How do the supports change the result?

A stiffer support raises the critical speed. For the same shaft, a cantilever has a factor 1.875 and the critical speed is 36 % of the simply supported value, while a shaft fixed at both ends has a factor 4.73 and a critical speed 2.27 times higher. The real bearings are not perfectly fixed or pinned, so the true value lies between the cases.

Why is the real critical speed lower than the result?

The calculator uses the weight of the shaft alone. Gears, pulleys, impellers and couplings add mass and lower the critical speed. The Dunkerley method combines the effect of each mass with the shaft. A flexible bearing or housing also lowers the value, so for a design with several masses, a full analysis is needed.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.