Skip to content
Omnikalc

Baseboard heater size calculator: heating power, length of baseboard and circuit load for a room

Enter the room area, the ceiling height, the insulation and the voltage to get the heating power in watts and BTU, the length of baseboard and the current.

Updated on
Your inputs
ft²

Value out of range

ft

Value out of range

W/ft

Value out of range

Results

Heating power needed

1,500 W

Heating power in BTU per hour
5,118 BTU/h
Length of baseboard needed
6.0 ft
Current drawn at full power
6.25 A
Heaters of this size that one 20 A circuit can carry (80 % rule)
2

The size of a baseboard heater depends on the area, the ceiling height and the insulation of the room. The baseboard heater size calculator gives the heating power in watts and BTU per hour, the length of baseboard, the current at full power and the number of heaters that one 20 A circuit can carry.

How the calculation works

  • Enter the floor area of the room and the ceiling height.
  • Choose the insulation and climate level: about 8 W per square foot for a well insulated room in a mild climate, 10 for an average one and 12 to 15 for a poorly insulated room or a cold climate.
  • Choose the voltage of the circuit and enter the output per foot of the baseboard (about 250 W per linear foot for most electric baseboards).
  • The calculator gives the power = area × W per ft² × (ceiling height / 8 ft), the BTU per hour, the length of baseboard, the current and the number of heaters that fit on a 20 A circuit.

Example

A room of 150 ft² with an 8 ft ceiling and an average insulation (10 W/ft²) needs 150 × 10 × (8 / 8) = 1,500 W, or 5,118 BTU/h. With baseboards of 250 W/ft, this is 6.0 ft of heater. On a 240 V circuit it draws 6.25 A, and one 20 A circuit, limited to 80 % (3,840 W), can carry 2 heaters of this size.

Why it matters

The calculator helps homeowners, renovators and electricians to choose electric baseboards for a bedroom, an office, a basement or an addition, and to plan the circuit. It avoids buying a heater that is too small to keep the room warm, or too big, which wastes money and cycles on and off.

Good to know

The watts per square foot are a rule of thumb for an approximate need. A real heat loss calculation uses the area of the walls, the windows, the insulation and the outdoor design temperature, and it is better for a cold climate or an unusual room. The 80 % rule on the circuit applies to continuous loads. Local codes set the wire size, the breaker and the clearances of a heater, and a licensed electrician should do the work.

The radiant floor heating calculator sizes a heated floor, the wood stove size calculator sizes a stove for a space, the boiler size calculator sizes a hydronic boiler, and the wall U-value calculator estimates the heat flow through a wall.

Frequently asked questions

How many watts of baseboard heater do I need?

A common rule is 10 watts per square foot of floor area for a room with an 8 ft ceiling and average insulation. A well insulated room in a mild climate may need only 8 watts per square foot, and a poorly insulated room or a cold climate needs 12 to 15. The value is multiplied by the ceiling height divided by 8 ft for higher rooms.

How long should the baseboard be?

Electric baseboards give about 250 watts per linear foot, so a 1,500 W need is covered by 6 ft of heater. It is better to use a long, low-density heater than a short, hot one, because it spreads the heat and works quietly. Place it under the window or along the coldest wall, where it stops the cold air from falling into the room.

Should I use 120 V or 240 V?

A 240 V heater draws half the current of a 120 V heater of the same power, so it needs thinner wires and loads the circuit less. A 20 A circuit at 240 V can feed 3,840 W of continuous heating with the 80 % rule, while a 20 A circuit at 120 V feeds only 1,920 W. Use 240 V for larger rooms and for all rooms where it is practical.

Is electric baseboard heating cheap to run?

Baseboard heaters convert all the electricity into heat, with an efficiency of 100 %, but electricity costs more per unit of heat than gas in most places. A heat pump provides 2 to 4 units of heat per unit of electricity and costs much less to run. Baseboards are cheap to install, and they suit small rooms, additions and spaces used a few hours a day.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.