Skip to content
Omnikalc

Beam on elastic foundation calculator: a long beam on a soil spring bed

Enter the point load, the modulus of subgrade reaction, the width and the stiffness of a long beam on soil to get the relative stiffness, the characteristic length, the maximum deflection, the maximum moment and the soil pressure.

Updated on
Your inputs
kips

Value out of range

pci

Value out of range

in

Value out of range

Msi

Value out of range

in⁴

Value out of range

Results

Maximum deflection under the load

0.0444 in

Relative stiffness β = (k / 4EI)^¼
0.0213 1/in
Characteristic length 1 / β
46.9 in
Maximum bending moment under the load
19.5 kip-ft
Maximum soil pressure under the load
8.89 psi
Minimum length for the infinite beam model (π / β)
12.3 ft

A beam on elastic foundation rests on a continuous soil that is modeled as a bed of springs. The beam on elastic foundation calculator applies the Winkler model for a long beam to give the relative stiffness, the characteristic length, the maximum deflection, the maximum moment and the soil pressure under a point load.

How the calculation works

  • Enter the point load on the beam, the modulus of subgrade reaction ks of the soil (about 100 to 400 pci for a medium sand or clay), the width of the beam and its modulus and moment of inertia.
  • The calculator turns ks into a foundation modulus per unit length k = ks × b, then finds the relative stiffness β = (k / 4EI)^¼, in 1/in.
  • For a long beam (the Winkler model), the maximum deflection under the load is y0 = P β / (2k), the maximum moment is M0 = P / (4β) and the maximum soil pressure is ks × y0.
  • It also shows the characteristic length 1 / β and the minimum length π / β for which the model of an infinite beam is accurate.

Example

A steel beam with I = 200 in⁴ and E = 29 Msi, 24 in wide, rests on a soil with ks = 200 pci and carries a 20 kip point load. The foundation modulus is k = 200 × 24 = 4,800 lb/in². The relative stiffness is β = (4,800 / (4 × 29,000,000 × 200))^¼ = 0.0213 1/in, and the characteristic length is 46.9 in. The maximum deflection is 20,000 × 0.0213 / (2 × 4,800) = 0.0444 in. The maximum moment is 20,000 / (4 × 0.0213) = 19.5 kip-ft and the soil pressure is 8.89 psi. The beam must be at least 12.3 ft long.

Why it matters

The calculator helps structural and geotechnical engineers, designers of strip footings, rails and pipelines, and students to estimate the bending of a beam that lies on the soil, to see the effect of the stiffness of the beam and the soil, and to check the soil pressure. It is the classic solution of the Hetényi beam.

Good to know

Choose the modulus of subgrade reaction from a load test or from the geotechnical report, and test the sensitivity with a range of values, since ks is uncertain. Check that the beam is long enough for the infinite beam model. For several loads, add the effects by superposition. Check the soil pressure against the allowable bearing pressure.

The beam deflection calculator covers simple supports, the section modulus calculator gives the bending stress, the bearing capacity calculator checks the soil pressure and the moment of inertia calculator gives I for a section.

Frequently asked questions

What is a beam on elastic foundation?

The Winkler model replaces the soil with a bed of independent springs. The reaction of the soil at each point is proportional to the deflection there, p = ks × y. A beam on this foundation carries the load by bending and by the reaction of the springs. The model describes strip footings, mat foundations, railway sleepers, pavement slabs and pipelines on soil, in a way that a rigid-footing assumption cannot.

What is the modulus of subgrade reaction?

The modulus of subgrade reaction ks is the pressure that produces a unit settlement of the soil, in pounds per cubic inch (pci) or MN/m³. It is not a property of the soil alone, since it depends on the size of the loaded area, but it is a good practical parameter. Typical values go from about 50 pci for a soft clay to 400 pci for a dense sand. It is found with a plate load test, or estimated from the soil type.

When is the beam long or short?

The relative stiffness β sets the length scale 1 / β of the beam. If the beam is longer than π / β, the load at the center barely affects the ends, and the formulas for an infinite beam are accurate. Between π / (4β) and π / β the beam is called of finite length, and the formulas need the end effects. Below π / (4β), the beam is almost rigid and its settlement is uniform.

What are the limits of the Winkler model?

The model ignores the shear between the springs: the soil outside the loaded area does not deflect, which is wrong for a real continuous soil. It gives good deflections but may underestimate the moments in a stiff soil. It also assumes that the soil can carry tension, which it cannot, so the beam must not lift off. The result is a first estimate. For a critical design, use the soil-structure interaction analysis.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.