Skip to content
Omnikalc

Bearing capacity calculator: how much load can the soil under a footing carry?

Enter the friction angle, cohesion, unit weight, footing size, depth and shape to get the ultimate and allowable bearing pressure.

Updated on
Your inputs
°

Value out of range

psf

Value out of range

pcf

Value out of range

ft

Value out of range

ft

Value out of range

Value out of range

Results

Allowable bearing pressure

6,254 psf

Good bearing: a shallow footing is likely suitable
Ultimate bearing capacity
18,762 psf
Overburden pressure at the footing base
360.0 psf
Bearing factor Nq
18.40
Bearing factor Nc
30.14
Bearing factor Nγ
22.40

Before pouring a footing, someone must check that the ground can carry the load. The bearing capacity calculator takes the friction angle, the cohesion, the unit weight of the soil, the footing width, the depth of its base, the shape and a factor of safety, and gives the allowable bearing pressure, the ultimate capacity, the overburden pressure and the bearing factors Nq, Nc and Nγ.

How the calculation works

  • Enter the soil strength: the friction angle φ and the cohesion c, usually from a geotechnical report. Enter the unit weight of the soil too.
  • Enter the width B and the depth Df of the footing base, and choose its shape.
  • The ultimate capacity is q ult = c × Nc × sc + q × Nq + 0.5 × γ × B × Nγ × sγ, where q is the soil pressure at the footing base, γ × Df. The bearing factors come from φ: Nq = e^(π tan φ) × tan²(45° + φ/2), Nc = (Nq − 1) ÷ tan φ and Nγ = 2 × (Nq + 1) × tan φ.
  • Dividing by the factor of safety, normally 3, gives the allowable bearing pressure. Shape factors raise or lower the cohesion and width terms for square and round footings.

Example

A square footing is 4 ft wide with its base 3 ft deep, on soil with φ = 30°, c = 200 psf and γ = 120 pcf. The factors are Nq = 18.40, Nc = 30.14 and Nγ = 22.40. The overburden is 120 × 3 = 360 psf. The three terms are 1.3 × 200 × 30.14 = 7,836, 360 × 18.40 = 6,624 and 0.5 × 120 × 4 × 22.40 × 0.8 = 4,301, so the ultimate capacity is 18,762 psf. With a factor of safety of 3, the allowable pressure is 6,254 psf, or about 6.3 ksf.

Why it matters

The soil is often the weak link in a foundation. A quick estimate shows whether a footing is in the right range, how much a wider or deeper footing helps and which parameter matters most. Students use it to follow the textbook method, and owners use it to understand a geotechnical report.

Good to know

The result is an estimate for a vertical, centred load on a level site above the water table. Real soils vary with depth, and the soil strength needed for the calculation comes from lab tests or field tests. Local codes set presumptive values and may require a geotechnical investigation. A qualified engineer must approve a real design.

The footing size calculator turns a load into a footing area, the retaining wall calculator covers walls, the flagpole footing calculator sizes small deep footings, and the factor of safety calculator helps choose margins.

Frequently asked questions

What is bearing capacity?

It is the largest pressure that a foundation can put on the soil before the soil fails in shear. The ultimate value is the load at failure, and the allowable value divides it by a factor of safety, normally between 2.5 and 3. Settlement is checked separately and often controls the final design.

What are the three terms of the equation?

The first term is the strength from cohesion, the second comes from the weight of the soil above the base, which holds the footing down and confines the soil below, and the third from the friction under the width of the footing. Wide footings on sand gain mostly from the third term, and footings on clay from the first.

Which factors does the calculator use?

It follows Terzaghi's equation and shape factors. For the bearing factors, it uses the Prandtl-Reissner values for Nq and Nc and the Vesic value for Nγ, which are common in textbooks today. Terzaghi's own factors differ somewhat, and some codes use others, so results can differ by tens of percent.

What does it leave out?

The calculator ignores the water table, which can cut the capacity by half when it reaches the base, as well as eccentric loads, inclined loads, sloping ground and layered soils. Soil parameters need to come from tests. A geotechnical engineer must confirm any foundation design, particularly for buildings.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.