Skip to content
Omnikalc

Belleville washer (disc spring) load calculator

Enter the diameters, the thickness, the cone height and the deflection to get the load, the flat load and the load and height of a stack in series and parallel.

Updated on
Your inputs
mm

Value out of range

mm

Value out of range

mm

Value out of range

mm

Value out of range

mm

Value out of range

GPa

Value out of range

Value out of range

Value out of range

Value out of range

Results

Load of one washer at this deflection

2,375 N

Diameter ratio De ÷ Di
1.969
Geometry constant K1
0.6878
Load of one washer when flat
4,634 N
Load of the stack
4,750 N
Deflection of the stack
1.50 mm
Free height of the stack
15.30 mm
Ratio h0 ÷ t
0.55

The Belleville washer calculator gives the diameter ratio, the load of one washer at a given deflection, the load when flat, and the load, deflection and free height of a stack in parallel and in series.

How the calculation works

  • Enter the outside and inside diameters, the thickness and the cone height of the free washer.
  • Enter the deflection of each washer, the modulus and the Poisson ratio of the steel.
  • Enter the number of washers in parallel and of groups in series for the stack.

Example

A washer of 50 mm by 25.4 mm and 2 mm thick, with a cone height of 1.1 mm, has a ratio of 0.55 and a diameter ratio of 1.969. It supports 2,375 N at 0.5 mm and 4,634 N when flat. A stack of 2 in parallel and 3 in series carries 4,750 N over 1.50 mm and has a free height of 15.30 mm.

Why it matters

The calculator helps designers of clutches, bolted joints, tools and valves who use disc springs to give a high load in a small space, and who need to size the stack for a load and a travel.

Good to know

The formula neglects the friction at the edges and the effect of the thickness on the contact radius, so the real load is a few percent higher for a loading and lower for an unloading. Series stacks must be guided to avoid tilting, and the number of washers in series should stay under a few tens. Check the stress at the inner edge with the data of the maker for the fatigue life, and use hardened, preferably standard washers (DIN 2093). Make sure that the bolt remains in the elastic range if the stack preloads a joint.

The compression spring calculator handles coil springs, the torsion spring calculator the angular ones, the leaf spring calculator the flat ones and the bolt torque calculator sets the preload of a joint that a stack can maintain.

Frequently asked questions

How is the load of a disc spring calculated?

The calculator uses the Almen and László formula, F = 4E / (1 − ν²) × t⁴ / (K1 × De²) × (δ / t) × [(h0 / t − δ / t)(h0 / t − δ / 2t) + 1], where K1 depends on the diameter ratio De / Di. It gives the load of one washer for a deflection δ. At the flat position, δ equals the cone height h0, and the load is 4E / (1 − ν²) × t⁴ × h0 / (K1 × De² × t).

What is the ratio h0 / t?

The ratio of the cone height to the thickness fixes the shape of the load curve. Below about 0.4 the curve is almost linear, around 0.4 to 1.3 it bends and becomes flat for ratios near 1.4, and above 1.4 the washer snaps through, which is useful for constant-load springs but needs a different design. The usual range is from 0.4 to 1.3.

What is the difference between series and parallel stacks?

Washers stacked in the same direction (parallel) multiply the load and keep the same deflection. Washers stacked alternately (series) add the deflections and keep the load. Mixed stacks combine both: n washers in parallel in each group and m groups in series give n times the load and m times the deflection.

How far can I compress a disc spring?

The working range is usually 15 to 75 % of the cone height, which keeps the load curve predictable and the stress low. Full flattening makes the load rise sharply and risks a permanent set. For fatigue loading, stay between 15 and 50 %, use a preload, and add washers or a guide pin to center the stack.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.