Skip to content
Omnikalc

Leaf spring deflection and stress calculator

Enter the load, the span, the number of leaves and their width and thickness to get the deflection, the spring rate, the stress and the safety factor.

Updated on
Your inputs
N

Value out of range

mm

Value out of range

Value out of range

mm

Value out of range

mm

Value out of range

GPa

Value out of range

MPa

Value out of range

Results

Deflection

100.6 mm

Spring rate
29.81 N/mm
Maximum bending stress
500 MPa
Safety factor against yield
2.20
Energy stored
151.0 J
Load at yield
6,600 N

The leaf spring calculator gives the deflection, the spring rate, the maximum bending stress, the safety factor against yield, the stored energy and the load at yield of a multi-leaf spring.

How the calculation works

  • Choose the type: semi-elliptic with a central load, or cantilever with an end load.
  • Enter the load, the span or length, the number of leaves and their width and thickness.
  • Enter the modulus and the yield strength of the steel to get the safety factor.

Example

A spring of 5 leaves of 50 mm by 6 mm and 1000 mm span, under 3000 N, deflects 100.6 mm, a rate of 29.81 N/mm. The bending stress is 500 MPa, a safety factor of 2.20 against yield, the spring stores 151.0 J and would reach yield at 6,600 N.

Why it matters

The calculator helps designers of vehicle and trailer suspensions, machine builders, restorers of old vehicles and makers who need a first estimate of a leaf spring, or who want to know whether a spare spring will fit the load.

Good to know

The formulas assume leaves of the same thickness and width, a graduated length so that the stress is the same in every leaf, and a rectangular section. Real springs use a master leaf with an eye and extra leaves of different lengths, so treat the result as an estimate. Use the load per spring, not the load of the whole axle, and add the dynamic factor of 2 to 3 for the shocks of the road. Check the fatigue life with a lower stress limit, and use shot peening and a good steel for a long life. Measure the real deflection under a known load to confirm the rate.

The compression spring calculator handles coil springs, the torsion spring calculator the angular ones, the spring-mass calculator gives the frequency of a sprung load and the beam deflection calculator treats a solid beam under the same load.

Frequently asked questions

How is the deflection of a leaf spring calculated?

For a semi-elliptic spring loaded at the center, the deflection is δ = 3 × F × L³ / (8 × E × n × b × t³), where F is the load, L the span, E the modulus, n the number of leaves, b their width and t their thickness. A cantilever spring loaded at the end deflects δ = 6 × F × L³ / (E × n × b × t³). The leaves are assumed to be graduated and to slide without friction.

What stress does the calculator give?

The maximum bending stress is σ = 3 × F × L / (2 × n × b × t²) for the semi-elliptic type and 6 × F × L / (n × b × t²) for the cantilever. It acts on the outer fiber of the longest leaf at the point of load. For safe fatigue life, the stress is kept well under the yield strength, often under 60 % of it for suspension springs.

Why is the real spring a bit stiffer?

In a real stack, the friction between the leaves and the clamping at the center add a little stiffness and damping, so the measured rate is usually 5 to 15 % higher than the ideal one. The formula is a good first estimate for design and for checking a spring that you already have.

How can I make the spring softer?

The deflection is inversely proportional to the third power of the thickness and directly proportional to the cube of the span. Thinner leaves or a longer span soften the spring a lot, while more leaves or wider ones soften it only proportionally. Keep the stress in check, because a softer spring sees the same stress for the same load only if the thickness is kept.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.