Skip to content
Omnikalc

Sewer infiltration allowance calculator: acceptance limit of a sanitary sewer

Enter the diameter, the length, the allowance of the specification and the measured infiltration to get the allowable infiltration per day and per hour and the ratio of the measured to the allowable.

Updated on
Your inputs
in

Value out of range

ft

Value out of range

gal/day

Value out of range

Results

Allowable infiltration per day

1,212 gal/day

Length of the section
0.758 mi
Allowable infiltration per hour
50.5 gal/h
Ratio of the measured to the allowable
0.74
The infiltration is within the allowance

The sewer infiltration allowance calculator gives the length of the section, the allowable infiltration per day, the allowable infiltration per hour and the ratio of the measured infiltration to the allowable for a sanitary sewer, from the diameter, the length and the allowance of the specification.

How the calculation works

  • Enter the diameter and the length of the sewer section.
  • Choose the allowance given by the specification, in gallons per inch of diameter per mile per day.
  • Enter the measured infiltration to get the allowable infiltration per day and per hour and the ratio of the measured to the allowable.

Example

A sewer of 8 in is 4,000 ft long, which is 4,000 / 5,280 = 0.758 mi. With an allowance of 200 gal/in/mi/day, the allowable infiltration is 200 × 8 × 0.758 = 1,212 gal/day, or 1,212 / 24 = 50.5 gal/h. A measured infiltration of 900 gal/day gives a ratio of 900 / 1,212 = 0.74, which is within the allowance.

Why it matters

The calculator helps sewer contractors, inspectors, utility engineers and students to prepare the acceptance test of a new sewer, to see if the measured infiltration is within the specification and to compare the effect of the diameter and the length.

Good to know

Read the allowance, the method and the duration of the test in the project specification, and test each section before the backfill is completed if the contract allows it. Check the joints and the manhole connections carefully during the installation, because most of the leaks are there. If the infiltration is over the limit, find the leak with a camera or a smoke test and repair it before retesting. Keep the test records with the as-built drawings, so that the owner can compare the rate of the infiltration in the years that follow.

The Manning equation calculator relates the flow and the slope of the sewer, the pipe flow velocity calculator checks the velocity, the sewer line replacement cost calculator estimates the replacement and the wet well volume calculator sizes the pumping station.

Frequently asked questions

What is the infiltration allowance of a sewer?

The infiltration is the groundwater that enters a sanitary sewer through the joints, the cracks and the manholes. The specification gives an allowance, a maximum rate per inch of diameter per mile of pipe per day, that the contractor must meet in the acceptance test. A common value is 200 gallons per inch per mile per day, and a strict specification can use 100 or even less.

How is the infiltration measured?

The infiltration is measured at the end of the construction, by measuring the flow at a weir or a manhole when the groundwater is high, or by an exfiltration test, in which the pipe is filled with water and the loss is measured. The air test and the vacuum test of the manholes are other methods. The method and the duration of the test are given by the specification of the project.

Why is infiltration important?

The infiltration takes a part of the capacity of the sewer and of the treatment plant, and it increases the cost of the pumping and of the treatment. A sewer with many leaks can overflow in a wet season, and the soil can enter the pipe and cause a void under the road. A good installation of the joints and of the manholes is the best way to keep the infiltration low.

What are the limits of the calculator?

The calculator uses the simple allowance per inch of diameter and per mile and does not include the manholes, which have their own allowance in many specifications, the service connections, the effect of the groundwater level or the inflow from the surface water. The allowance and the test are those of the project specification, which can be different from the common values.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.